manualshive.com logo in svg

Rosemount 8732 Series, Справочное руководство

Поделиться
Скачать
Rosemount 8732 Series Скачать руководство пользователя страница 134

Reference Manual

00809-0100-4663, Rev BA

January 2010

Rosemount 8732

C-14

Troubleshooting the 
8714i Meter Verification 
Test

In the event that the 8714i Meter Verification test fails, the following steps can 
be used to determine the appropriate course of action. Begin by reviewing the 
8714i results to determine the specific test that failed.

Figure C-1. Troubleshooting the 
8714i Meter Verification Test 
Table

8714i Meter Verification 
Functionality

The 8714i Meter Verification diagnostic functions by taking a baseline sensor 
signature and then comparing measurements taken during the verification 
test to these baseline results. 

Sensor Signature Values

The sensor signature describes the magnetic behavior of the sensor. Based 
on Faraday’s law, the induced voltage measured on the electrodes is 
proportional to the magnetic field strength. Thus, any changes in the magnetic 
field will result in a calibration shift of the sensor. Having the transmitter take 
an initial sensor signature when first installed will provide the baseline for the 
verification tests that are done in the future. There are three specific 
measurements that are stored in the transmitter’s non-volatile memory that 
are used when performing the calibration verification.

Coil Circuit Resistance

The Coil Circuit Resistance is a measurement of the coil circuit health. This 
value is used as a baseline to determine if the coil circuit is still operating 
correctly when the 8714i Meter Verification diagnostic is initiated.

Coil Signature

The Coil Signature is a measurement of the magnetic field strength. This 
value is used as a baseline to determine if a sensor calibration shift has 
occurred when the 8714i Meter Verification diagnostic is initiated.

Test

Potential Causes of Failure

Steps to Correct

Transmitter Verification Test 
Failed

• Unstable flow rate during 

the verification test

• Noise in the process
• Transmitter drift
• Faulty electronics

• Perform the test with no 

flow in the pipe

• Check calibration with an 

external standard like the 
8714D

• Perform a digital trim
• Replace the electronics

Sensor Verification Failed

• Moisture in the terminal 

block of the sensor

• Calibration shift caused by 

heat cycling or vibration

• Remove the sensor and 

send back for recalibration.

Coil Circuit Health Failed

• Moisture in the terminal 

block of the sensor

• Shorted Coil

• Perform the sensor checks 

detailed on page 6-8.

Electrode Circuit Health 
Failed

• Moisture in the terminal 

block of the sensor

• Coated Electrodes
• Shorted Electrodes

• Perform the sensor checks 

detailed on page 6-8.

375

Transducer Block, Diagnostics, Advanced Diagnostics, 8714i Meter Verification, 
Sensor Signature, Signature Values, Coil Resistance

AMS Tab

Config/Setup, 8714i 

375

Transducer Block, Diagnostics, Advanced Diagnostics, 8714i Meter Verification, 
Sensor Signature, Signature Values, Coil Signature

AMS Tab

Config/Setup, 8714i 

Содержание 8732 Series































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды