manualshive.com logo in svg

Rosemount 8732 Series, Справочное руководство

Поделиться
Скачать
Rosemount 8732 Series Скачать руководство пользователя страница 45

Reference Manual 

00809-0100-4663, Rev BA
January 2010

4-7

Rosemount 8732

Measurements 

View the measured values taken during the meter verification process. These 
values are compared to the signature values to determine if the test passes or 
fails. Values are shown for the Coil Resistance, Coil Signature, and Electrode 
Resistance.

Coil Resistance

 

View the measured value for the coil resistance taken during the meter 
verification test.

Coil Signature 

View the measured value for the coil signature taken during the meter 
verification test.

Electrode Resistance 

View the measured value for the electrode resistance taken during the meter 
verification test.

Licensing 

If a diagnostic suite was not ordered initially, advanced diagnostics can be 
licensed in the field. Access the licensing information from this menu. For 
more details on licensing, see Appendix C: Diagnostics.

License Status 

Determine if a diagnostics suite has been licensed, and if so, which 
diagnostics are available for activation.

License Key 

A license key is required to activate diagnostics in the field if the diagnostic 
suite was not initially ordered. This menu allows for gathering of necessary 
data to generate a license key and also the ability to enter the license key 
once it has been received.

Device ID 

This function displays the Device ID and Software Revision for the transmitter. 
Both of these pieces of information are required to generate a license key.

License Key 

Allows you to enter a license key to activate a diagnostic suite.

375 Transducer Block, Diagnostics, Advanced Diagnostics, 8714i Meter Verification

375 Transducer Block, Diagnostics, Advanced Diagnostics, 8714i Meter Verification, 

measurements

375 Transducer Block, Diagnostics, Advanced Diagnostics, 8714i Meter Verification, 

measurements

375 Transducer Block, Diagnostics, Advanced Diagnostics, 8714i Meter Verification, 

measurements

375 Transducer Block, Diagnostics, Advanced Diagnostics

375 Transducer Block, Diagnostics, Advanced Diagnostics, Licensing

375 Transducer Block, Diagnostics, Advanced Diagnostics, Licensing

375 Transducer Block, Diagnostics, Advanced Diagnostics, Licensing, License Key

375 Transducer Block, Diagnostics, Advanced Diagnostics, Licensing, License Key

Содержание 8732 Series































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды