manualshive.com logo in svg

Rosemount 1199, Справочное руководство

Поделиться
Скачать
Rosemount 1199 Скачать руководство пользователя страница 62

Reference Manual

00809-0100-4002, Rev BB

November 2012

Rosemount 1199

6-2

.

Table 6-1.  Troubleshooting Seal Systems.

PROBLEM
NO RESPONSE
Symptom

Potential Source

Corrective Action

No output

Electrical problem

See the troubleshooting section of the transmitter manual for more 
extensive information. 
Check for adequate voltage to the transmitter.
Check the milliampere rating of the power supply against the total 
current being drawn for all transmitters being powered.
Check for shorts and multiple grounds.
Check for proper polarity at the transmitter terminal. 
Check loop impedances.

See if the transmitter is in a multidrop mode.The multidrop mode locks 
the output at 4 mA.

SLOW RESPONSE
Symptom

Potential Source

Corrective Action

Slow response

Damping too high

Cold Temperature

See the “Damping Adjustment” information in the Calibration section of 
the transmitter manual.
Fill fluid viscosity is temperature dependent. Less viscous fill fluid 
enhances time response. Heat traced capillaries can be added as an 
option to maintain constant temperatures to fill fluid.

DRIFTING
Symptom

Potential Source

Corrective Action

Drifting

Temperature effect

If pressure measurement is changing, refer to “Understanding Seal 
System Performance” on page 2-2 for more information.
Running Instrument Toolkit will calculate the expected performance for 
the seal system. Refer to “Instrument Toolkit: Seal Ordering and 
Application Process” on page 2-8 for more information.

Output reads negative 
pressure

Mounting effect

The output will read negative as the remote fill fluid is applying pressure 
to the low side. See Section 4: Ranging the Transmitter.

Will not respond to change in 
pressure

Damaged diaphragm

Remove seal and inspect diaphragm

Do not use higher than the specified voltage to check the loop, or the 
transmitter electronics may be damaged.

Содержание 1199



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды