manualshive.com logo in svg

Rosemount 1199, Справочное руководство

Поделиться
Скачать
Rosemount 1199 Скачать руководство пользователя страница 57

Reference Manual 

00809-0100-4002, Rev BB
November 2012

5-7

Rosemount 1199

FILL FLUID 
SPECIFICATIONS – 
NEOBEE M-20

Neobee M-20 Description

Neobee M-20 is the most commonly used fill fluid for sanitary applications 
because of its low viscosity and thermal stability. It is a polyol diester of short 
chain naturally derived fatty acids (coconut oils). Neobee is approved under 
21CFR 172.856 as a direct food additive and under 21CFR 174.5 as an 
indirect food additive. It is soluble in alcohol containing up to 20% water, has a 
smooth non-oily feel and unusually low viscosity, similar to Silicone 200. 
Neobee properties make it a good all purpose fill fluid. On colder applications 
the response time should be evaluated due to increased viscosity. Neobee 
M-5 is also available as an ‘M’ number. It offers lower vapor pressure and 
improved thermal stability. However, viscosity more than doubles compared to 
M-20.

Temperature Limits

At Atm Pressure

-15 to 225 °C (5 to 437 °F)

Viscosity at 25 °C (77 °F)

9.8 cs

Specific Gravity @ 25 °C (77 °F)

0.94

Coefficient of Thermal Expansion

0.001008 cc/cc/C (0.00056 cc/cc/F)

Chemical Composition

Derived from coconut oil and propylene glycol: 
Dicaprylate/Dicaprate

CAS Number

68583-51-7

Содержание 1199



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды