Roland VersaEXPRESS RF-640 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 132

background image

4

Part of

Practice

79

Fully Utilize the Media Heating System

What Is the Media Heating System?

This machine is equipped with a media heating system that warms the media. You use this mainly to improve
ink adhesion and also dry the ink. You can adjust the temperature settings to match the type of media and
the print speed.

* By using an optional dryer, you can speed up drying of the ink more. Contact your authorized Roland DG

Corp. dealer or us.



P. 83, "Using an Optional Dryer"

WARNING

CAUTION: high temperatures

The platen and dryer become hot. Exercise caution to avoid fire or burns.

WARNING

Remove any loaded media or switch off the sub power when printing is

not being performed.

The continued application of heat at a single location may cause fire or produce

toxic gases.

WARNING

Never use media that cannot withstand the heat.

Doing so may result in fire or the release of toxic gases, or may degrade the

media.

WARNING

Never use the platen or dryer for any purpose for which they are not

intended, such as to dry clothing.

Doing so may cause overheating, resulting in fire or accident.

Use at an ambient temperature of 20 to 32°C (68 to 90°F).

If the machine is used at an ambient temperature lower than 20°C (68°F), then depending on the type or
width of the media, wrinkling or temperature-caused unevenness may occur. If this happens, try lowering the
temperature of the media heating system by about 2°C. To obtain stable print results, however, the machine
should be used at an ambient temperature of 20 to 32°C (68 to 90°F).

Making the Temperature Setting for the Media Heating System

Procedure



Press

.



Press

several times until the screen on the left appears.

Press

.

FUNCTION

HEATER CONFIG

Print heater

You use this mainly to improve ink adhesion.

Dryer

You use this to speed up drying of

the ink.

«
...
79
80
81
82
83
...
»

Содержание VersaEXPRESS RF-640





































































































































Отзывы:

Нет отзывов

Похожие инструкции для VersaEXPRESS RF-640

Бренд: Jeppesen Страницы: 39

Бренд: Weidmuller Страницы: 308

Бренд: MIMAKI Страницы: 8

Бренд: MIMAKI Страницы: 8

Бренд: MIMAKI Страницы: 24

Бренд: MIMAKI Страницы: 110

Бренд: MIMAKI Страницы: 142

Бренд: MIMAKI Страницы: 170

Бренд: MIMAKI Страницы: 274

Бренд: MIMAKI Страницы: 144

Бренд: MIMAKI Страницы: 172

Бренд: MIMAKI Страницы: 152

Бренд: MIMAKI Страницы: 172

Бренд: MIMAKI Страницы: 186

Бренд: MUTOH Страницы: 98

Бренд: MUTOH Страницы: 141

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды