Roland VersaEXPRESS RF-640 Скачать руководство пользователя страница 119

Страница: 119 / 132

117

A Message Appears

These are the main messages that appear on the machine's display screen to prompt correct

operation. They do not indicate any error. Follow the prompts and take action accordingly.

■

] (RF-640) [1

■

] (RF-640A)

The machine ran out of the ink. Replace the ink cartridge indicated by the flashing number with a new ink
cartridge.

[PRESS THE POWER KEY TO CLEAN]

This appears when the machine has been unused for about one month. Switch on the sub power once a month.



P. 74, "When Not in Use for a Prolonged Period"

[CLOSE THE COVER (FRONT COVER, COVER L or COVER R]

Close the Front cover, Cover L, or Cover R. For safety, the print-head carriage does not operate while a cover
is open.

[SHEET NOT LOADED SETUP SHEET]

Load media. This message appears when an attempt to perform a printing test was made while no media
was loaded.

[EMPTY DRAIN BOTTLE]

This appears when a certain amount of discharged fluid collects in the drain bottle. If this screen appears,
discard the discharged fluid in the drain bottle.



P. 51, "Discard Discharged Fluid"

[INSTALL DRAIN BOTTLE]

Check whether the drain bottle is installed. Install the drain bottle, then press



P. 51, "Discard Discharged Fluid"

[NOW HEATING...]

Wait until the media heating system reaches the preset temperature. Printing starts when

lights up.

You can stop printing by holding down

for one second or longer while this is displayed. Pressing

makes printing start immediately, without waiting to reach the preset temperature.

[TIME FOR MAINTENANCE]

It is time to clean the print heads manually. After verifying, press



P. 59, "Manual Cleaning"

Содержание VersaEXPRESS RF-640





































































































































Результаты поиска

Содержание VersaEXPRESS RF-640

Отзывы:

Похожие инструкции для VersaEXPRESS RF-640

Бренды по названию

Популярные бренды

Roland VersaEXPRESS RF-640, Руководство пользователя

Результаты поиска

Содержание VersaEXPRESS RF-640

Отзывы:

Похожие инструкции для VersaEXPRESS RF-640

Бренды по названию

Популярные бренды