Roland VersaEXPRESS RF-640 Скачать руководство пользователя страница 104

Страница: 104 / 132

Administrators

102

System Management of Machine

Setting for the Menu Language and the Units of Measurement

This sets the language and units of measurement displayed on the display screen of the operation panel.

Procedure



Hold down

and switch on the sub power.



Use

to select the display (menu) language.

Press

to enable the setting.



Use

to select the measurement unit for length.

Press

to enable the setting.



Use

to select to the measurement unit for

temperature.

Press

to enable the setting.

Default Setting

[MENU LANGUAGE]: ENGLISH
[LENGTH UNIT]: mm
[TEMP. UNIT]: °C

Setting the Interval Until Activation of the Sleep Mode (Power Saving Function)

Procedure



Press



Press

several times until the screen on the left appears.

Press



Press

several times until the screen on the left appears

Press

twice.



Use

to make the setting.

Press

to enable the setting.



Press

to go back to the original screen.

Default Setting

[INTERVAL]: 30min

MENU LANGUAGE

ENGLISH

LENGTH UNIT

INCH

TEMP. UNIT

SUB MENU

SLEEP

INTERVAL

30min

15min

Содержание VersaEXPRESS RF-640





































































































































Результаты поиска

Содержание VersaEXPRESS RF-640

Отзывы:

Похожие инструкции для VersaEXPRESS RF-640

Бренды по названию

Популярные бренды

Roland VersaEXPRESS RF-640, Руководство пользователя

Результаты поиска

Содержание VersaEXPRESS RF-640

Отзывы:

Похожие инструкции для VersaEXPRESS RF-640

Бренды по названию

Популярные бренды