Roland VersaEXPRESS RF-640 Скачать руководство пользователя страница 100

Страница: 100 / 132

Administrators

Print Operation Management

Printing a System Report

This prints system information, including a list of setting values.

Procedure



Press



Press

several times until the screen on the left appears.

Press



Press

several times until the screen on the left appears.

Press

Start printing.



Press

to go back to the original screen.

Determining What Happens When Ink Runs Out (RF-640A only)

This lets you change, according to your purpose, the operation that takes place when an ink cartridge becomes
empty.

Procedure



Press



Press

several times until the screen on the left appears.

Press



Press

several times until the screen on the left appears.

Press

twice.



Press

to select a setting.

STOP: Printing pauses immediately when a cartridge becomes empty.
CONT (continue): Printing does not stop when a cartridge becomes empty.
When a cartridge becomes empty, a warning beep sounds.

Press

to enable the setting.



Press

to go back to the original screen.

SUB MENU

SYSTEM REPORT

SUB MENU

INK CONTROL

EMPTY MODE

STOP CONT.

Содержание VersaEXPRESS RF-640





































































































































Результаты поиска

Содержание VersaEXPRESS RF-640

Отзывы:

Похожие инструкции для VersaEXPRESS RF-640

Бренды по названию

Популярные бренды

Roland VersaEXPRESS RF-640, Руководство пользователя

Результаты поиска

Содержание VersaEXPRESS RF-640

Отзывы:

Похожие инструкции для VersaEXPRESS RF-640

Бренды по названию

Популярные бренды