Roland VersaEXPRESS RF-640 Скачать руководство пользователя страница 63

Страница: 63 / 132

Maintenance

Maintenance that Should Be Performed More Than Once a Month



Attach the cover L.

The print-head carriage moves to the left of the machine.

Cover L

Hook



Remove the cover L.



Remove the cover R.



Preparations are complete when this screen appears.

Clean using the cleaning stick.



Touch the location shown in the figure to

discharge any static electricity.



Check that the cut rail has been removed.

If the cut rail is not removed, close all the covers and restart the operation from the beginning. If you
continue the operation as the cut rail remains attached, the print heads might get broken.

CLOSE COVER L

OPEN COVER L

FINISHED?

Screw

Hook

Cover R

Содержание VersaEXPRESS RF-640





































































































































Результаты поиска

Содержание VersaEXPRESS RF-640

Отзывы:

Похожие инструкции для VersaEXPRESS RF-640

Бренды по названию

Популярные бренды

Roland VersaEXPRESS RF-640, Руководство пользователя

Результаты поиска

Содержание VersaEXPRESS RF-640

Отзывы:

Похожие инструкции для VersaEXPRESS RF-640

Бренды по названию

Популярные бренды