Roland VersaEXPRESS RF-640 Скачать руководство пользователя страница 47

Страница: 47 / 132

Basic

Operation

Printing



Press

to display the screen on the left.

Press

The media is cut off.

You can make the setting in the software RIP for automatic media cutoff after printing has finished. For
information on how to make the setting, refer to the documentation of the software RIP you're using.

FUNCTION

SHEET CUT

Printed area

Knife guide

Reflective tape

The media is

moved forward

and cut along this

line.

Cut-off Operations

When the media clamps are attached, the screen on the left appears.
Open the front cover and detach the left and right media clamps
and press



Be sure to detach the media clamps. Performing cutoff with the media clamps remaining attached

may cause the operation to be interrupted due to detection of the media clamps.



If the media clamps are present on the machine when the setting to execute automatic cutoff of

the media is made on the RIP software, the media clamps are detected and no cutoff operation
is performed.



Before you're performing cutoff, never use

to pull the media back. Unless the end of the

media has been pulled out to a location to the front of the platen, cutoff may not be performed
smoothly.

Give Attention to Media Composition



For some types of media, cutoff is not possible.



Some types of media may remain on the platen after cutoff. If the media remains on the platen,

remove it by hand.

REMOVE

MEDIA CLAMPS

Содержание VersaEXPRESS RF-640





































































































































Результаты поиска

Содержание VersaEXPRESS RF-640

Отзывы:

Похожие инструкции для VersaEXPRESS RF-640

Бренды по названию

Популярные бренды

Roland VersaEXPRESS RF-640, Руководство пользователя

Результаты поиска

Содержание VersaEXPRESS RF-640

Отзывы:

Похожие инструкции для VersaEXPRESS RF-640

Бренды по названию

Популярные бренды