An Error Message Ap p ears
6
Troubleshooting
18 8
Message
Situation/error cause
Action
[ C A N ' T P RI N T C RO P
C O N TI N U E ? ]
The size of the data including
the crop marks is larger than
the printing area of the load-
ed media.
To continue performing output without correcting
this, press [ENTER]. At this time, the crop marks
and the portion extending beyond the printing
area are not output. To stop output, stop sending
data from the computer, and then raise the loading
lever. Make the printing area wider, for example by
replacing the media with a larger piece of media,
and then send the data again.
The size of the data being
output is too small.
Make the horizontal-direction (scan-direction) size
of the data at least 65 mm (2.6 in.). To continue
performing output without correcting this, press
[ENTER]. At this time, the data is output without
printing the crop marks. To stop output, stop
sending data from the computer, and then raise
the loading lever. Increase the size of the data, and
then send the data again. There is no limitation on
the size of the data in the media-feed direction.
[ S H E E T TO O S M A L L
C O N TI N U E ? ]
The size of the data is larger
than the printing area of the
loaded media.
To continue performing output without correcting
this, press [ENTER]. At this time, the portion extend-
ing beyond the printing area is not output. To stop
output, stop sending data from the computer, and
then raise the loading lever. Make the printing area
wider, for example by replacing the media with
a larger piece of media, and then send the data
again.
[ D A TA E RRO R
C A N C E L I N G . . . ]
Output was stopped because
a problem was found in the
received data.
Operation cannot be continued. Check for a prob-
lem with the connector cable or the computer, and
then redo the operations from the step of loading
the media.
[ S H E E T S E T E RRO R
S E T A G A I N ]
The loading lever was lowered
while no media was loaded.
Raise the loading lever, place media at the correct
location, then lower the lever again.
"
P . 2 9 " S t e p 1 : L o a d i n g Ro l l M e d i a ( S e t u p o f M e d i a ) "
"
P . 7 0 " L o a d i n g S h e e t M e d i a ( S e t u p o f M e d i a ) "
[EDGE DETECTION] is set to "EN-
ABLE," but transparent media
was loaded.
Raise the loading lever, set the [EDGE DETECTION]
menu item to "DISABLE," then reload the media.
"
P . 12 5 " U si n g Tr a n sp
a r e n t M e d i a "
The loaded media is too small. Press any button to clear the error. Replace the
media with media of a usable size.
[ P I N C H RO L L E RRO R
L O W
E R P I N C H RO L L ]
This message appears when
the loading lever was raised
during initialization or after
the media was loaded.
Press any key to clear the error. Otherwise, the error
is cleared automatically after a short wait. Never
move the loading lever while output is in progress.
[ P I N C H RO L L E RRO R
I N V A L I D L E F T ( RI G H T)
P O S ]
The left (right) pinch roller is
positioned at a location where
it cannot pinch the media.
Raise the loading lever and move the pinch roller
to the correct location.
"
P . 2 9 " S t e p 1 : L o a d i n g Ro l l M e d i a ( S e t u p o f M e d i a ) "
"
P . 7 0 " L o a d i n g S h e e t M e d i a ( S e t u p o f M e d i a ) "
