Roland Color CAMM PC-50 Скачать руководство пользователя страница 4

2

The carriage moves simultaneously
when the power is switched on.

When pulling the
power cord from an
electrical socket, be
sure to grip the plug.

 This indicates a point requiring particular care to ensure safe use of the product.

Typographic
Conventions

This manual uses typographic conventions
which are outlined at the right.

: Failure to heed this message will result in serious injury or death.

: Failure to heed this message may result in serious injury or death.

: Failure to heed this message may result in minor injury.

: Indicates important information to prevent machine breakdown or

malfunction and ensure correct use.

: Indicates a handy tip or advice regarding use.

NOTICE

 To Ensure Safe Use

Never disassemble or
modify this product.

Handle the power cord with care.

Do not step on or damage the power
cord, or allow heavy objects to be placed
atop it.  Failure to heed may result in
electrocution
or fire.

Ensure the safety of the area
around the platen before
switching on the power.

Do not install in an
unstable or high location.

Do not install the machine on
the edge of a table, or it may
fall.

Handle the blade
with care.

Do not allow liquids, metal
objects or flammables
inside the machine.

Fire or breakdown may result.

Do not inadvertently
allow the hands, hair, or
necktie near the carriage
while in operation.

Do not place hands
near the platen while
in operation.

To Ensure Correct Use

ON

 About the Labels

Affixed to the Unit

These labels are affixed to the body of this product.
 The following figure describes the location.

This product is a
precision instrument and
must be handled with
care.

NOTICE

Do not install in an area
subject to dust, high
humidity or poor
ventilation.

NOTICE

Do not connect to an AC
outlet that supplies other
than the specified
voltage.

NOTICE

When the unit is not in use
for an extended period,
detach the electrical plug
from the AC outlet.

NOTICE

3

2

1

100 V

117 V

220 V

240 V

240 V

Do not allow the hands near
the platen while in operation.

Typographic Conventions / To Ensure Safe Use

Содержание Color CAMM PC-50


























Отзывы: