Rohde & Schwarz 1321.1211.02 Скачать руководство пользователя страница 227

Страница: 227 / 621

Spectrum Analyzer Mode

R&S

Cable Rider ZPH

220

User Manual 1321.0950.02 ─ 07

The R&S Cable Rider ZPH can also handle 75

Ω

systems. The R&S Cable Rider ZPH

does not select a 75

Ω

RF input. Instead it selects a 75

Ω

matching pad connected at

the RF input. The 50/75

Ω

matching pad R&S RAZ is recommended for 75

Ω

matching

(see recommended accessories). The R&S Cable Rider ZPH automatically considers
the conversion factor when a value of 75

Ω

is set.

1. Press the [SCALE/AMPT] key.

2. Select the "Att / Amp / Imp" softkey.

3. Select the impedance you need.

You can also use other matching pads (e.g. R&S RAM or R&S FSH-Z38) by acti-
vating transducer factors.

8.2.3.8

Using Transducer Factors

For more information, see

Chapter 8.4, "Using Transducer Factors"

on page 249.

8.2.4

Configuring the Tracking Generator

The tracking generator provides a stimulus signal in the spectrum measurement mode.

Configuring the signal source

You can select the type of generator source in three different ways.

●

"Tracking"
Output frequency depends on current measurement frequency.

●

"CW"
Output frequency can be defined.

●

"Coupled CW"
Output frequency is coupled to the current measurement center frequency.

1. Press [MEAS] key.

2. Select "Source" softkey.

The R&S Cable Rider ZPH opens the signal source menu.

3. Select "Source Mode" softkey.

The R&S Cable Rider ZPH opens the submenu that contains the signal source
selection.

4. Select the required signal source.

● If selected signal source is "Tracking", the R&S Cable Rider ZPH opens an

input field to specify the tracking generator offset frequency, "TG Offset".

● If selected signal source is "CW", the R&S Cable Rider ZPH opens an input

field to specify the continuous waveform frequency, "CW Freq".

Configuring Spectrum Measurements

Содержание 1321.1211.02














































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 1321.1211.02

Отзывы:

Бренды по названию

Популярные бренды

Rohde & Schwarz 1321.1211.02, Руководство пользователя

Результаты поиска

Содержание 1321.1211.02

Отзывы:

Бренды по названию

Популярные бренды