manualshive.com logo in svg

Rockwell Automation DEVICENET 1771-SDN, Руководство пользователя, Страница: 43 / 139

Поделиться
Скачать
Rockwell Automation DEVICENET 1771-SDN Скачать руководство пользователя страница 43

Publication 1771-6.5.132 - June 2000

Hardware Setup        

3-5

Installing the 1785-ENET
Ethernet Module

To go online to the PLC-5 processor via Ethernet, you must install a 
1785-ENET module in the 1771 I/O chassis.

The Ethernet module is shipped with a 58-pin connector header that 
attaches to the PLC-5 processor.

1.

Attach the connector header to the PLC-5 processor.

2.

Use the captive screws to connect the interface module to the 
processor.

Status Indicator

Transmit Indicator

External Transceiver
Fuse

Channel 3A:
15-pin AUI
Connector Port

IMPORTANT

Make sure you carefully align the pins and holes 
before you press the connector header into the 
processor. If you improperly align them, you will 
bend the connector header pins when you press 
them together. Do not use excessive force on the 
connector header when seating it into the processor. 
You do not need to key the connector.

Push the exposed pins
into the holes on the
PLC-5 processor.

Attach the interface 
module to this end.

Connector
Header

Содержание DEVICENET 1771-SDN












































































































































Отзывы:

Нет отзывов