Rockwell Automation DEVICENET 1771-SDN Скачать руководство пользователя страница 120

Страница: 120 / 139

Publication 1771-6.5.132 - June 2000

C-2

Installing and Configuring the DH+ Communications Driver

Configuring the 1784-KTX
Communications Driver

After installing the card in the computer, you must run

RSLinx

configure the communications driver.

Start the

RSLinx

software.

From the

Communications

menu select

Configure Drivers

The

Configure Drivers

window will appear:

From the list of

Available Drivers

, select the

1784-KT/KTX(D)/PKTX(D)

driver

from the pull-down list and

click on

Add/New

When prompted for a name for the new driver, select the default
name assigned by the system,

AB_KT-1

The device’s configuration window will open:

Содержание DEVICENET 1771-SDN












































































































































Результаты поиска

Содержание DEVICENET 1771-SDN

Отзывы:

Похожие инструкции для DEVICENET 1771-SDN

Бренды по названию

Популярные бренды

Rockwell Automation DEVICENET 1771-SDN, Руководство пользователя

Результаты поиска

Содержание DEVICENET 1771-SDN

Отзывы:

Похожие инструкции для DEVICENET 1771-SDN

Бренды по названию

Популярные бренды