Robur Caldaria 100.2 Condensing+ export Скачать руководство пользователя страница 6

Страница: 6 / 56

Warnings

III

added.

▶

2014/30/EC "Electromagnetic Compatibility Directive" as

amended and added.

▶

2014/35/EC "Low Voltage Directive" as amended and added.

▶

2006/42/EC "Machine Directive" as amended and added.

Furthermore, they comply with the requirements of the follow-

ing standards:

▶

EN 677 Specific requirements for condensing boilers with

nominal heat input up to 70 kW.

▶

EN 483 Type C boilers of nominal heat input not exceeding

70 kW.

▶

EN 15502 Gas-fired central heating boilers.

Other applicable provisions and standards

The design, installation, operation and maintenance of the sys-

tems shall be carried out in compliance with current applicable

regulations, depending on the Country and location, and in ac-

cordance with the manufacturer's instructions. In particular, reg-

ulations regarding the following shall be complied with:

▶

Gas systems and equipment.

▶

Electrical systems and equipment.

▶

Heating systems employing condensing boilers.

▶

Environmental protection and combustion products ex-

haust.

▶

Fire safety and prevention.

▶

Any other applicable law, standard and regulation.

III.3

EXCLUSIONS OF LIABILITY AND

WARRANTY

Any contractual or extra-contractual liability of the man-

ufacturer for any damage caused by incorrect installa-

tion and/or improper use and/or failure to comply with

regulations and with the manufacturer's directions/in-

structions shall be disclaimed.

In particular, the warranty on the appliance may be ren-

dered void by the following conditions:

Incorrect installation.

Misuse.

Failure to comply with the manufacturer's indications on

installation, use and maintenance.

Alteration or modification of the product or any part

thereof.

Extreme operational conditions or however outside of

the operational ranges set forth by the manufacturer.

Damages caused by external agents such as salts, chlo-

rine, sulphur or other chemical substances contained in

the installation water or present in the air of the instal-

lation site.

Abnormal actions transmitted to the appliance by the

plant or installation (mechanical stresses, pressure, vi-

brations, thermal expansion, electrical surges...).

Accidental damages or due to force majeure.

Содержание Caldaria 100.2 Condensing+ export

























































Результаты поиска

Содержание Caldaria 100.2 Condensing+ export

Отзывы:

Бренды по названию

Популярные бренды

Robur Caldaria 100.2 Condensing+ export, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Caldaria 100.2 Condensing+ export

Отзывы:

Бренды по названию

Популярные бренды