Robur Caldaria 100.2 Condensing+ export Скачать руководство пользователя

Страница: 42 / 56

First start-up

P33 (4)

Modbus communication baud rate

Not used

Do not modify

P34

Status of the additional solar board

Not used

Do not modify

P69

Activation of the auxiliary relay on the SVZ additional board

Not used

Do not modify

P70

Water flow control enable during start-up

It allows the verification, at each switch on, of the correct operation of the circulator.

0 ÷ 1

0 = disabled
1 = enabled

1. If the setting is changed, the change must be made on both

the master and the slave module.

2. To activate the DHW service, parameter P01 must be set to

the value 0 and parameter P32 must be set to the appropri-

ate value according to the DHW request device used (DHW

buffer tank probe OSND011, DHW buffer tank thermostat

or cascade controller ODSP039). Setting parameter P01 to

the value 0 enables the parameters related to DHW produc-

tion, i.e. P09, P10, P11, P15, P17, P21, P32 and the DHW anti-

freeze functions, the DHW probe error and the diverter valve

anti-locking function.

3. In presence of cascade controller ODSP039 (optional), if

DHW production is managed by the controller itself, param-

eter P01 must be set to value 0 and parameter P32 to value

2. Parameters P15, P17, P21 will be disabled as they are man-

aged directly by the controller.

4. Parameters P26, P33 relating to Modbus settings must be

configured only in the presence of the cascade controller

ODSP039 (optional), following the instructions provided in

the manual supplied with the controller itself.

5.4.4

Climatic curves

Figure 5.6

Climatic curves

Tm Delivery temperature
Te

Outdoor temperature

Kd Heating control value

Te (°C)

45 MAX

Tm (°C)

-5

-10

-15

-20

25 MIN

Kd = 0

Kd = 5

Kd = 15

Kd = 20

Kd = 25 Kd = 30

Kd = 10

5.4.5

Blower frequencies

Table 5.4

Minimum and maximum blower frequencies

Boiler

Gas type

Measurement unit

Frequency (heating/DHW) (1)

minimum

maximum

Caldaria 35

G20

203

G25

203

G25.3

203

G30

195

G31

203

Caldaria 55.1
Caldaria 100.2

G20

247

G25

247

G25.3

247

G30

230

G31

240

Check parameters P10 and P11 for DHW, P12 and P13 for heating.

Содержание Caldaria 100.2 Condensing+ export

























































Результаты поиска

Содержание Caldaria 100.2 Condensing+ export

Отзывы:

Похожие инструкции для Caldaria 100.2 Condensing+ export

Бренды по названию

Популярные бренды

Robur Caldaria 100.2 Condensing+ export, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Caldaria 100.2 Condensing+ export

Отзывы:

Похожие инструкции для Caldaria 100.2 Condensing+ export

Бренды по названию

Популярные бренды