manualshive.com logo in svg

Robur Caldaria 100.2 Condensing+ export, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Robur Caldaria 100.2 Condensing+ export Скачать руководство пользователя страница 39

First start-up 

Installation, use and maintenance manual – Caldaria Con export 

39

5

P06

DHW position holding function

By enabling this function it is possible to keep the DHW diverter valve in the DHW 
position for a time equal to the DHW post-circulation (parameter P09), in order to 
exploit this heat as well.

0 ÷ 1

0

0 = disabled
1 = enabled

P07

Heating timing

You can set the minimum time in which the burner is kept off once the heating 
temperature has reached the setpoint.

0 ÷ 90

36

Value in multiples of 5 s (default 36 x 
5 = 180 s)

P08

Post-circulation heating timing

It is possible to set the operating time of the pump, in heating mode, after the main 
burner has been switched off due to the intervention of the room thermostat.

0 ÷ 90

36

Value in multiples of 5 s (default 36 x 
5 = 180 s)

P09

Post-circulation DHW timing

It is possible to set the operating time of the pump, for the DHW service, after the 
setpoint in the DHW buffer tank has been reached.

0 ÷ 90

24

Value in multiples of 5 s (default 24 x 
5 = 120 s)

P10

Minimum blower speed adjustment for DHW

It is possible to set the minimum speed of the blower for the DHW service, which 
corresponds to the minimum power of the burner during a DHW request (see Figure 
5.8 

p. 43). The value is preset according to the set power (parameter P00) and the 

type of gas (parameter P02).

45 ÷ P11

--

Value in hertz (1 Hz = 30 RPM)

P11

Maximum blower speed adjustment for DHW

It is possible to set the maximum speed of the blower for the DHW service, which 
corresponds to the maximum power of the burner during a DHW request (see Figure 
5.8 

p. 43). The value is preset according to the set power (parameter P00) and the 

type of gas (parameter P02).

P10 ÷ 203

--

Value in hertz (1 Hz = 30 RPM)

P12

Minimum blower speed adjustment for heating

It is possible to set the minimum speed of the blower for the heating service, which 
corresponds to the minimum power of the burner during a heating request (see 
Figure 5.8 

p. 43). The value is preset according to the set power (parameter P00) 

and the type of gas (parameter P02).

45 ÷ P13

--

Value in hertz (1 Hz = 30 RPM)

P13

Maximum blower speed adjustment for heating

It is possible to set the maximum speed of the blower for the heating service, which 
corresponds to the maximum power of the burner during a heating request (see 
Figure 5.8 

p. 43). The value is preset according to the set power (parameter P00) 

and the type of gas (parameter P02).

P12 ÷ 203

--

Value in hertz (1 Hz = 30 RPM)

P14

Starting step adjustment

It is possible to set the blower speed during the start-up phases. The value is preset 
according to the set power (parameter P00) and the type of gas (parameter P02).

P10 ÷ 203

--

Value in hertz (1 Hz = 30 RPM)

P15 (1)

Legionella function

WARNING: burn hazard. See Paragraph 5.8 

p. 46.

0 ÷ 1

1

0 = disabled
1 = enabled

P16

Setting the climate curve (only with outdoor probe OSND009 connected)

The OSND009 outdoor temperature probe may be connected and acts by auto-
matically changing the outlet temperature according to the measured outdoor 
temperature. The extent of the correction depends on the set heating control value 
Kd (Figure 5.6 

p. 42). The choice of the curve is determined by the maximum outlet 

temperature Tm and the minimum outdoor temperature Te, taking into account the 
degree of insulation of the building. The values of the outlet temperatures Tm refer to 
standard systems 30-80 °C or floor systems 25-45 °C. The type of system can be set 
using parameter P03.

0 ÷ 30

25

The numbering of the value corre-
sponds to the 'Kd' curves of the graph 
(Figure 5.6 

p. 42)

P17

Centralized control function via CS contact

By enabling this parameter you can deactivate specific services when closing the CS 
contact (Paragraph 4.4 

p. 32).

0 ÷ 1

0

0 = disabled
1 = enabled

P18

0-10 V industrial bus drive enable

The 0-10 V industrial bus input can be enabled or disabled to set burner power or 
delivery temperature via the external bus.

0 ÷ 2

0

0 = disabled
1 = temperature control mode
2 = power control mode

P19

Min heating setpoint

It is possible to set the minimum user-adjustable heating temperature.

20 ÷ 40

30

Value in °C

P20

Max heating setpoint

It is possible to set the maximum user-adjustable heating temperature.

40 ÷ 90

80

Value in °C

P21 (1)

Maximum setpoint for DHW

It is possible to set the maximum user-adjustable DHW temperature.

45 ÷ 75

60

Value in °C

P22

Δt delivery-return setpoint

It is possible to set the temperature difference between delivery and return.

0

10 ÷ 40

20

0 = disabled
Value in °C

P23

Modulating pump minimum speed

It is possible to set the minimum speed value of the modulating pump during a 
request for space heating operation.

50 ÷ 70

60

Value in percentage

P24

Modulating pump maximum speed

It is possible to set the maximum speed value of the modulating pump during a 
request for space heating operation.

70 ÷ 100

100

Value in percentage

P25 (1)

DHW buffer tank setpoint differential

It is possible to set the differential value with respect to the DHW setpoint at which 
the DHW buffer tank charge is activated. For example, with the DHW setpoint at 50 
°C and the parameter value at 5 °C, DHW buffer tank recharging starts at 45 °C (50-5) 
and stops when the storage reaches the DHW setpoint. The parameter is only active if 
the buffer tank probe OSND011 is connected.

3 ÷ 9

9

Value in °C

Содержание Caldaria 100.2 Condensing+ export

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды