manualshive.com logo in svg

Robur Caldaria 100.2 Condensing+ export, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Robur Caldaria 100.2 Condensing+ export Скачать руководство пользователя страница 38

First start-up

38

5

P24

Modulating pump maximum speed

It is possible to set the maximum speed value of the modulating pump during a 
request for space heating operation.

70 ÷ 100

100

Value in percentage

P25 (1)

DHW buffer tank setpoint differential

It is possible to set the differential value with respect to the DHW setpoint at which 
the DHW buffer tank charge is activated. For example, with the DHW setpoint at 50 
°C and the parameter value at 5 °C, DHW buffer tank recharging starts at 45 °C (50-5) 
and stops when the storage reaches the DHW setpoint. The parameter is only active if 
the buffer tank probe OSND011 is connected.

3 ÷ 9

9

Value in °C

P26 (3)

Modbus address

Not used

-

1

Do not modify

P27 (3)

Modbus communication baud rate

Not used

-

0

Do not modify

P28 (3)

Modbus mode

Not used

-

2

Do not modify

P29

Post-circulation heating Δt

It is possible to set the temperature difference from the main burner shut down due 
to the room thermostat, below which the pump is deactivated for the heating service.

0 ÷ 25

0

Value in °C

P30

Post-circulation DHW Δt

It is possible to set the temperature difference from the deactivation of the DHW 
request to the pump deactivation for the DHW service.

0 ÷ 25

10

Value in °C

P31

Heating antifreeze temperature setting

It is possible to set the temperature of the water in the heating system at which the 
antifreeze protection is activated.

5 ÷ 12

12

Value in °C

P32

Flowmeter enable

Not used

-

0

Do not modify

P33

Minimum water flow setting

Not used

-

28

Do not modify

P34

Activation of the auxiliary relay on the SVZ additional board

Not used

-

0

Do not modify

P35

Water flow control enable during start-up

It allows the verification, at each switch on, of the correct operation of the circulator.

0 ÷ 1

1

0 = disabled
1 = enabled

1.  In presence of cascade controller ODSP039 (optional), if 

DHW production is managed by the controller itself, param-

eter P01 must be set to value 0. Parameters P15, P21, P25 will 

be inhibited as they are managed directly by the controller.

2.  By setting a value of parameter P01 other than 5 (heating on-

ly), the parameters relating to DHW production, i.e. P09, P10, 

P11, P15, P21, P25, P30 and the DHW antifreeze functions, 

DHW probe error and diverter valve anti-locking are enabled.

3.  Parameters P26, P27, P28 relating to Modbus settings must 

be configured only in the presence of the cascade controller 

ODSP039 (optional), following the instructions provided in 

the manual supplied with the controller itself.

5.4.2 

   Caldaria  55.1

Table 5.2  

 Caldaria 55.1 electronic board parameters

Parameter Description

Range

Default

Setting

P00

Boiler model selection

0 ÷ 10

10

10 = Caldaria 55.1

P01 (1) (2) Boiler type selection

0 ÷ 5

5

0 = heating and buffer tank DHW 
(with DHW function controlled by 
cascade controller ODSP039)
1 = do not use
2 = heating and buffer tank DHW
3 = heating and buffer tank DHW 
(DHW setpoint increased by 7 °C)
4 = do not use
5 = heating only

P02

Gas type selection

WARNING: before changing the parameter value, read the instructions in Paragraph 
5.6 

p. 45.

0 ÷ 1

0

0 = G20, G25, G25.3
1 = LPG, G30, G31

P03

Heating temperature setting

0 ÷ 1

0

0 = standard (30÷80 °C)
1 = reduced (25÷45 °C)

P04

Heating run-up

It is possible to set the time, during the start-up phase, that the boiler takes to reach 
the maximum set power (for the space heating service).

0 ÷ 4

3

0 = disabled
1 = 50 s
2 = 100 s
3 = 200 s
4 = 400 s

P05

Anti-water hammer function

Enabling this function delays the DHW contact, for a time equal to the set value, 
during the activation in DHW mode.

0 ÷ 20

2

0 = disabled
Value in seconds

Содержание Caldaria 100.2 Condensing+ export

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды