Robur Caldaria 100.2 Condensing+ export Скачать руководство пользователя

Страница: 20 / 56

Transport and positioning

TRANSPORT AND POSITIONING

2.1

WARNINGS

Damage from transport or installation

The manufacturer shall not be liable for any damage dur-

ing appliance transport and installation.

On-site inspection

Upon arrival at the site, ensure there is no transport dam-

age on packing or boiler panels.

After removing the packing materials, ensure the appli-

ance is intact and complete.

Packing

Only remove the packing after placing the appliance on

site.

Do not leave parts of the packing within the reach of

children (plastic, polystyrene, nails...) since they are po-

tentially dangerous.

Weight

The lifting equipment must be suitable for the load.

Do not stand under suspended loads.

2.2

HANDLING

Handling and lifting

▶

Always handle the appliance in its packing, as delivered by

the factory.

▶

Comply with safety regulations at the installation site.

In the event of handling with forklift or pallet truck,

comply with the handling instructions shown on the

packing.

2.3

MINIMUM CLEARANCE DISTANCES

Keep the appliance away from combustible or flam-

mable materials or components, in compliance with ap-

plicable regulations.

In order to allow periodic maintenance of the boiler, the

installation must take place outside, respecting the dis-

tances indicated in Figure 2.1

p. 20 and in any case at

a height not exceeding 3 metres from a walking sur-

face to ensure correct maintenance in safety.

Figure 2.1

Minimum clearance distances

> 250 mm

> 500 mm, < 3 m

> 1000 mm

> 200 mm

Содержание Caldaria 100.2 Condensing+ export

























































Результаты поиска

Содержание Caldaria 100.2 Condensing+ export

Отзывы:

Похожие инструкции для Caldaria 100.2 Condensing+ export

Бренды по названию

Популярные бренды

Robur Caldaria 100.2 Condensing+ export, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Caldaria 100.2 Condensing+ export

Отзывы:

Похожие инструкции для Caldaria 100.2 Condensing+ export

Бренды по названию

Популярные бренды