RoboVent Spire MLS-01-5500-10 Скачать руководство пользователя страница 29

Страница: 29 / 68

ROBOVENT • SPIRE SERIES OWNER’S MANUAL

Commissioning Your Unit

The following items checked during the start-up/commissioning process, as applicable to
your specific layout:

1. Check the electrical connection to the collector and ensure there are no loose wires.

2. Check the compressed air that was hooked-up to the RoboVent supplied regulator

and confirm it is clean, dry, and set to 85 psi.

3. Check the blower rotation on each motor to confirm it is spinning correctly.

4. Perform basic system check to ensure it is functional:

a. Check to ensure blower turns on when touched on HMI

b. Perform a valve check (See maintenance guideline for more information on how

to perform this check) to ensure that each pulse valve is operational.

5. Check to ensure the fire suppression (FM200) tubing is hooked up correctly, if

applicable.

6. Check the FM200 gauge to ensure your suppression tank is charged, if applicable.

7. Check that the filter differential tubes (running from the control panel to the reading

ports) are correctly connected; ensure the filter pressure is reading correctly on the
HMI control screen.

8. Check to ensure every bolt was installed during the collector assembly.

9. Check and confirm operation of other custom equipment options (ex: Intake

Dampers, etc.).

10. Check the ductwork and ensure it is connected and sealed correctly.

11. Check the filter and control door gaskets to ensure consistent seal during operation.

12. Check and ensure collector seams were properly sealed during the assembly process.

13. Verify and record the velocity (FPM) through the Delta3 spark arrestor, if applicable.

a. Specific velocity range is required through the Delta3 to prevent sparks from

getting through.

14. Verify and record the velocity (FPM) and airflow (CFM) for the entire system

SECTION 600

Start-up/Commissioning and Balancing

Содержание Spire MLS-01-5500-10





































































Результаты поиска

Содержание Spire MLS-01-5500-10

Отзывы:

Похожие инструкции для Spire MLS-01-5500-10

Бренды по названию

Популярные бренды

RoboVent Spire MLS-01-5500-10, Руководство пользователя

Результаты поиска

Содержание Spire MLS-01-5500-10

Отзывы:

Похожие инструкции для Spire MLS-01-5500-10

Бренды по названию

Популярные бренды