background image

KIT# 52285-1

03/17/09

KS

R O A D M A S T E R

,

  I N C.

ITEM 

QTY 

NAME 

       

 

 

MATERIAL

1........... 2 ..........1/2" x 5" BOLT ......................................................................350107-00
2........... 2 ..........1/2" x 4 1/2" BOLT ................................................................350106-00
3........... 8 ..........1/2" x 1 1/2" BOLT ................................................................350095-00
4........... 12 ........1/2" LOCK WASHER ...........................................................350309-00
5........... 8 ..........1/2" HEX NUT ......................................................................350258-00
6........... 8 ..........3/8" x 1 1/4" BOLT ................................................................350056-00
7........... 8 ..........3/8" LOCK WASHER ...........................................................350305-00
8........... 8 ..........3/8" HEX NUTS ....................................................................350254-00
9........... 2 ..........QUICK  LINK .........................................................................200008-00
10......... 2 ..........SAFETY CABLE 10" ............................................................500646-10
11 ......... 2 ..........1" O.D. x 0.219 WALL x 2" PIPE SPACER ..........................A-001056
12......... 2 ..........1/4" x 2" x 2" ROUND HOLE BACKING PLATE ..................A-001066
13......... 2 ..........SIDE  PLATE .........................................................................A-002587
14......... 2 ..........1" O.D. x 0.219 WALL x 3/8" 6 DEGREE PIPE SPACER ....A-002588
15......... 2 ..........UPPER  BRACE ...................................................................B-001144
16......... 4 ..........1/4" x 1" x 2" THREADED BACKING PLATE W/ ROD ........C-001483
17......... 1 ..........MAIN  RECEIVER .................................................................C-001653
18......... 1 ..........DRIVER SIDE ARM .............................................................C-001654
19......... 1 ..........PASSENGER SIDE ARM.....................................................C-001655
20......... 1 ..........INSERT ................................................................................25-4259-00

ROADMASTER, Inc.   6110 NE 127th Ave.   Vancouver, WA 98682    1-800-669-9690    fax 360-735-9300   www.roadmasterinc.com

MOUNTING BRACKET KIT

INSTALLATION INSTRUCTIONS

Содержание 52285-1











Отзывы: