manualshive.com logo in svg

Rinnai Ember 600, Руководство по установке

Поделиться
Скачать
Rinnai Ember 600 Скачать руководство пользователя страница 33

  

Ember Installation Guide: 12890-F 06-21 

  |   

33

Mock chimney - extended horizontal

Flueing options

 Max. 600 mm 

 Max. 2 m

Max. 2 m

255

Important

The horizontal flue length must not 

be greater than the vertical.

590 mm

1

2

3

3

4

5

Flue components

1

Ember adaptor (R3653)

Refer p. 30 for clearance to 

combustible information for the 

Ember adaptor.

Maximum length can’t be more 

than 600 mm due to the heat 

from the colinear flexi flues.

Horizontal wall terminal (R3650)

2

Horizontal flashing kit (R3646)

3

Flue pipe(s) or flue extension

The horizontal run of flue pipe 

must have a 20 mm 

rise

 for every 

1 m 

towards

 the flue termination. 

NEVER allow the flue pipe to 

run downwards towards the flue 

terminal. A downwards slope 

can trap heat and become a fire 

hazard.

 

4

Flue elbow 90 

°

 (R3643)

Maximum number of 90° bends is 

one.

5

If installing the Rinnai Ember into a purpose built chimney breast or chase, 

which is not open to the roof space of the building, you will need to add 

cavity vents. 

Heat from the fire lost through the outer skin of the appliance or the flue 

system will not be able to adequately vent. This can lead to a build up of excess heat in the cavity. 

In some cases the fire may overheat and the overheat safety mechanisms may operate.

Adding two vents of at least 200 cm

2

, one at floor level, and one at ceiling level, will allow adequate 

airflow in a cavity of approximately 1.2 m wide x 2.4 m high and 0.8 m deep. With an additional 

benefit that the ventilation of the cavity will return some of this heat into the room.

Please 

note

Содержание Ember 600









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды