Rinnai Ember 600 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 40

background image

Ember Installation Guide: 12890-F 06-21

|

15

Make sure the chimney cap is

weathertight. Flexi flue also needs to be

secured to the flue cowl using the clamps

provided—these need to be riveted/

screwed in place to reduce the risk of

movement.

Check the size of the chimney before

doing anything. It needs to be at least

200 x 200 mm for the colinear flexi flue to

fit down.

When dropping the flexi flue down the

chimney make sure you have the intake

and exhaust flues in the correct position.

The intake is on the left.

Flexi flues clamped and riveted/screwed

in place to the engine spigot plate. Due

to the weight it’s best to support the

underside of the plate to stop the flexi

flues from extending too much.

Base of masonry enclosure

MUST BE

level and allow free movement of the

appliance for maintenance and servicing.

The Ember engine must be secured

to the enclosure via the top and side

flanges. This can be done directly into the

enclosure, into the infill panel or masonry

frame using the side brackets provided.

Intake Ø 75 mm left hand side.

Exhaust Ø 100 mm right hand side.

Maximum flue length is 8 m.

«
...
13
14
15
16
17
...
»

Содержание Ember 600









































Отзывы:

Нет отзывов

Похожие инструкции для Ember 600

Бренд: Manfrotto Страницы: 2

Бренд: Manfrotto Страницы: 2

Бренд: GE Страницы: 20

Бренд: Quadra-Fire Страницы: 28

Бренд: GE Страницы: 2

Бренд: KARPO Fly Страницы: 13

Бренд: zenitech Страницы: 16

Бренд: Darfon Страницы: 28

Бренд: VanEssa mobilcamping Страницы: 8

Бренд: Garmin Страницы: 22

Бренд: R-Go Страницы: 2

Бренд: R&S Страницы: 52

Бренд: barbas Страницы: 60

Бренд: Atlas Copco Страницы: 88

Бренд: Empire Comfort Systems Страницы: 4

Бренд: Desa Страницы: 4

Бренд: DEFA Страницы: 9

BAYPORT-41 GLASS

Бренд: kozy heat Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды