manualshive.com logo in svg

Rinnai Arriva, Руководство по установке дымохода

Поделиться
Скачать
Rinnai Arriva Скачать руководство пользователя страница 4

 

 4

  

 |   

Arriva/Evolve flue installation guide: 10726-I 09-21

About this guide

This guide is to outline the most common types of flue installations and to provide an overview 

of how to assemble the various flue components. If you have an installation that varies from this 

guide, please contact Rinnai.

Flue installation differences between the Arriva and Evolve

• 

Direct flue kits differ

 

Due to the size of the Evolve unit and the cavity dimensions, the only direct flue kit available 

for the Evolve is the ASPDFK. The direct mushroom flue kits that can be used for the Arriva are 

not suitable as the telescopic exhaust section of the Evolve is not long enough to connect to 

the flue transition of the mushroom flues.

 

 

  

EVOLVE MODELS

 

ASPDFK direct flue kit 

 

Mushroom direct flue kit

• 

Adaption flue kits differ

 

- Arriva uses the ASPKIT03, refer p.8

 

- Evolve uses the EVOKIT03, refer p.8

 

• 

How condensate is handled differs

 

For the Arriva a condensate drain kit needs to be installed, refer p.24. For the Evolve the 

condensate drain tube is connected directly to the condensate pipe on the heater, refer 

appendix 1 on p.25.

Содержание Arriva





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды