manualshive.com logo in svg

Rinnai Arriva, Руководство по установке дымохода

Поделиться
Скачать
Rinnai Arriva Скачать руководство пользователя страница 21

  

Arriva/Evolve flue installation guide: 10726-I 09-21

   |   

21

Steps to create a wall terminal

1.  Fit the supplied external wall plate over the outer pipe of the flue protrusion (arrow points up)

 

 

Once the external wall plate is in the correct position secure it to the wall using the three 22 mm 

screws into the wall plate holes. Secure the wall plate to the outer pipe using the two horizontal 

holes and the two 7 mm screws provided.

 

2.  Carefully cut through the outer and inner pipes 

ensuring the inner and outer are flush with 

the external wall plate

 as shown below. Take care to avoid cutting the external wall plate, and 

keep the cuts of the internal and external pipes as parallel as possible. Remove all burrs and 

swarf from the cut ends.

 

3.  Align the arrows of the metal flue terminal and wall plate to point in the 

same direction (must always point up) and screw the terminal to the 

external wall plate using the 22 mm screws into the holes provided.

Exterio

r wall

Exterio

r wall

Exterio

r wall

2° fall to the outside—

arrow points up

Images showing how final terminal should be installed

Approx. 14-16 mm

Please note

: The flue protrusion from the wall is approx. 14-16 mm. It must not be more than this as it will create a gap 

between the flue and the wall terminal, which will cause operational issues.

Содержание Arriva





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды