Rinnai Arriva Скачать руководство пользователя страница 24

Страница: 24 / 28

Arriva/Evolve flue installation guide: 10726-I 09-21

Arriva condensate drain kit connection

The condensate drain kit is provided with the ASPKIT03. It is used in vertical flue installations for

draining condensate back into the heater.

Rubber grommet

insertion point for

condensate tube

Condensate tube inserted

up to the 90° bend

Combustion air hose connection

REAR

Wire tie

Secure

Rubber drain

outlet

Condensate

hose

FRONT

Condensate tray

Condensate tube

Rubber grommet

for condensate tube

Short end towards rear of heater and long end towards front of heater

Condensate

tube

Condensate

drain hose

At least 10mm

penetration of

barb is required

Before connecting the condensate drain hose to the condensate trap ensure that there are no

kinks in the condensate drain hose. Also ensure the path of the condensate drain hose is kept

away from hot surfaces. Failure to install the condensate kit correctly may cause damage to the

heater and flue system.

1. Insert the barbed end of the condensate tube into the condensate drain hose. Ensure that the

barb penetrates the hose by at least 10 mm.

2. Locate the condensate tube insertion point, which is a rubber grommet found at the rear of the

heater, to the right of the combustion air hose connection.

3. Uncoil the condensate drain hose and secure it to the rear of the heater using the upper screw

of the combustion fan cover and the wire tie provided.

4. Connect the free end of the condensate drain hose to the rubber drain outlet of the condensate

trap by pushing the hose inside the rubber connection to a minimum of 20 mm, but not greater

than 30 mm (this can cause a blockage).

5. Place the condensate tray into the heater (short end first) making sure that the tray is centered

under the end of the condensate tube.

Содержание Arriva





























Результаты поиска

Содержание Arriva

Отзывы:

Бренды по названию

Популярные бренды

Rinnai Arriva, Руководство по установке дымохода

Результаты поиска

Содержание Arriva

Отзывы:

Бренды по названию

Популярные бренды