RINGSPANN DR 085 FHM-100 страница 26 Скачать руководство пользователя | Manualshive

Страница: 26 / 39

background image

Installation and operating instructions for

Rail Clamp DR 085/088 FHM

spring activated

– hydraulically released

E 09.797e

Issue: 14.09.2022

Version: 2

Drawn: BAHS

Checked: OHLM

Pages: 39

Page: 26

3.4 Hand pump operation oft he rail clamp

Use the hand pump (if supplied) to release open the rail clamp manually (without electric
current).

Refer to the corresponding hydraulic power unit for more information.

Information!

Refer to the corresponding hydraulic power unit for more information.

4

PERIODIC MAINTENANCE

Attention!

The rail clamps DR 085/088 FHM with diamond pads are intented for
purely static uses. Any dynamic braking requires a replacement of the
pads.

The rail should be free of lubricants and oils so that the coefficient of
friction does not drop. If this instruction is not observed, braking force
may be lost.

The air gap must be adjusted after replacing the friction block.

Attention!

When changing the friction block, replace the friction block according
to chapter 5. If this instruction is not observed, braking force may be
lost.

Only original RINGSPANN friction pads may be used.

«
...
24
25
26
27
28
...
»

Содержание DR 085 FHM-100








































Отзывы:

Нет отзывов

Похожие инструкции для DR 085 FHM-100

Бренд: Sagola Страницы: 8

Бренд: National Instruments Страницы: 16

Бренд: Jasco Страницы: 11

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ODA Страницы: 103

Бренд: Nitecore Страницы: 4

Бренд: KaVo Страницы: 4

ORTHOPANTOMOGRAPH OP 3D

Бренд: KaVo Страницы: 40

KEY Laser III 1243

Бренд: KaVo Страницы: 103

EXTRAmatic 9040

Бренд: KaVo Страницы: 56

ESTETICA E70 Vision

Бренд: KaVo Страницы: 48

Бренд: Kaya Safety Страницы: 5

Бренд: XTA Страницы: 20

Бренд: Kawai Страницы: 166

Бренд: Land Pride Страницы: 32

Бренд: Omlet Страницы: 2

Бренд: Omicron Страницы: 382

Бренд: Omicron Страницы: 188

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды