background image

50

© Heating and Hotwater Industry Council (HHIC)

www.centralheating.co.uk

www.hhic.co.uk

Benchmark Commissioning & 

Warranty Validation Service Record

It is a requirement that the boiler is installed and commissioned to the manufacturers’ 

To instigate the boiler warranty the boiler needs to be registered with the 
manufacturer within one month of the installation. The warranty rests with the  
end-user (consumer), and they should be made aware it is ultimately their 
responsibility to register with the manufacturer, within the allotted time period.

It is essential that the boiler is serviced in line with the manufacturers’ 
recommendations, at least annually. This must be carried out by a competent Gas 
Safe registered engineer. The service details should be recorded on the Benchmark 
Service and Interim Boiler Work Record and left with the householder. Failure to 
comply with the manufacturers’ servicing instructions and requirements will invalidate 
the warranty.

This Commissioning Checklist is to be completed in full by the competent person who commissioned the boiler as a means of demonstrating 
compliance with the appropriate Building Regulations and then handed to the customer to keep for future reference. 

Failure to install and commission according to the manufacturers’ instructions and complete this Benchmark Commissioning Checklist will invalidate the 
warranty. This does not affect the customer’s statutory rights.

Содержание 47-364-61

























































Отзывы: