27
NOTE:
please refer to section 4, section 4.1 and use the ap-
propriate PPE when carrying out any of the actions or proce-
dures contained within this section.
5.1 DELIVERY
Due to the weight of the appliance it may be necessary for two
people to lift and attach the appliance to its wall bracket. The
appliance is contained within a heavy-duty cardboard carton.
Lay the carton on the floor with the writing the correct way up.
5.2 CONTENTS
Contained within the carton is:
• the boiler
• the wall bracket
• carton template
• an accessories pack containing appliance service connections
and washers
• the instruction pack containing the installation, servicing & user
instructions, guarantee registration card and a 3-amp fuse.
5.3 UNPACKING
At the top of the carton pull both sides open – do not use a
knife – unfold the rest of the carton from around the appliance,
carefully remove all protective packaging from the appliance and
lay the accessories etc. to one side. Protective gloves should
be used to lift the appliance, the appliance back-frame should
be used for lifting points.
5.4 PREPARATION FOR MOUNTING THE
APPLIANCE
The appliance should be mounted on a smooth, vertical,
surface, which must be capable of supporting the full weight of
the appliance. Care should be exercised when determining the
position of the appliance with respect to hidden obstructions
such as pipes, cables, etc.
When the position of the appliance has been decided – using
the template supplied – carefully mark the position of the wall
mounting bracket and flue-hole (if applicable).
Top flue
5.5 FITTING THE FLUE
This appliance incorporates a ‘click-fit’ flue connection at the
top of the appliance.
5.5.1 CONCENTRIC HORIZONTAL FLUE
These instructions relate specifically to the installation of
this appliance with the Vokera 60/100mm ‘X-type’ (click-fit)
flue terminals and accessories. For specific instructions on
installing this appliance with an alternative Vokera flue system,
e.g. 80/125mm; please refer to the instructions supplied with
the specific flue system, or download the instructions from the
Vokera website. The appliance flue outlet elbow can be rotated
through 360º on its vertical axis. In addition the flue may be
extended from the outlet elbow in the horizontal plane (see 2.9).
A reduction must also be made to the maximum length (see
table below) when additional bends are used.
Reduction for additional bends
Bend
Reduction in maximum flue length for each bend
45º bend
1.0 metre
90º bend
1.0 metre
Horizontal flue terminals and accessories
Code
Description
Length
20122759
XF standard horizontal flue kit
TBC
20122761
XT telescopic flue kit
TBC
29450123 90-degree bend
N/A
29450124 45-degree bends (2)
N/A
29450125 500mm extension
500mm
29450126 1000mm extension
1000mm
29450127 2000mm extension
2000mm
29450128 Telescopic extension
372/519mm
522
Plume management kit
1370mm
529
100mm flue brackets (5)
N/A
Using the template provided (
A
), mark and drill a 125mm hole
for the passage of the flue pipe. Each horizontal terminal,
incorporates an incline on the inner (60mm) pipe; this enables
the terminal to be installed on a level plane. However any
extended horizontal flue runs must incorporate a 3-degree fall-
back from the flue terminal towards the appliance. The fixing
holes for the wall-mounting bracket should now be drilled and
plugged, an appropriate type and quantity of fixing should be
used to ensure that the bracket is mounted securely. Once the
bracket has been secured to the wall, mount the appliance
onto the bracket.
Fig. 11
flange installed
as standard
C
C
B
A
A
90° bend
FITTING THE HORIZONTAL FLUE KIT
Carefully measure the distance from the centre of the appliance
flue outlet to the edge of the finished outside wall (dimension X).
Add 65mm to dimension X to give you Dimension Y (see fig. 12).
Measure dimension Y from the terminal end of the concentric
flue pipe and cut off the excess ensuring any burrs are removed.
IMPORTANT:
The X-type flue terminals are supplied with
a sachet of silicone lubricant; smear a small amount of the
lubricant around both inner and outer connections, at both
ends of the flue bend.
NOTE:
Attach the decorative white plastic trim to the flue pipe
at this point if it’s required.
5. SECTION - INSTALLATION
