background image

2

1.  THINGS YOU SHOULD KNOW

1. THINGS YOU SHOULD KNOW ...................................................2
2. GETTING STARTED ....................................................................5
3. HOW TO.... .................................................................................10
4. WHAT IF  .....................................................................................10
SECTION 1 - DESIGN  PRINCIPLES AND OPERATING  

SEQUENCE ...................................................................................12
SECTION 2 - TECHNICAL DATA ..................................................13
SECTION 3 - CONTROL PANEL (REC10) ....................................17
SECTION 4 - GENERAL REQUIREMENTS (UK) .........................24
SECTION 4A - GENERAL REQUIREMENTS (EIRE) ....................25

SECTION 5 - INSTALLATION .......................................................27
SECTION 6 - COMMISSIONING ...................................................32
SECTION 7 - SERVICING INSTRUCTIONS ..................................42
SECTION 8 - CHECKS, ADJUSTMENTS AND FAULT FINDING ....43
SECTION 9 - LPG INSTRUCTIONS ..............................................48
Commissioning checklist ............................................................49

Benchmark ...............................................................................50-53

Vokèra Warranty Terms and conditions ................................54-55

USERS INSTRUCTIONS

INTRODUCTION

Dear Customer

Your Vokèra 

UNICA MAX

 boiler has been designed to meet and exceed the very latest standards in gas central heating technology, 

and if cared for, will give years of reliable use and efficiency. Please therefore take some time to read these instructions carefully.

Do’s and Don’t’s

Do

 ensure that the system pressure is periodically checked

Do

 ensure that the boiler is not used by children or unassisted disabled people

Do

 ensure that you know how to isolate the appliance in an emergency

Do

 ensure that you are familiar with the appliance controls

Do

 ensure that your installer has completed the appliance log book section

Do not

 attempt to remove the appliance casing or gain internal access

Do not

 hang clothes etc. over the appliance

Do not

 forget to have the appliance serviced annually.

This booklet is an integral part of the appliance. It is therefore necessary to ensure that the booklet is handed to the person responsible 

for the property in which the appliance is located/installed. A replacement copy can be obtained from Vokèra customer services.

  At the end of its life, the product should be not be disposed of as solid urban waste, but rather it should be handed over to a 

differentiated waste collection

 and/or recycling centre.

1.1  GAS APPLIANCES

Gas Safety (Installation and Use) Regulation (UK).

In the interests of your safety and that of others it is a legal 

requirement that all gas appliances are installed and correctly 

maintained by a competent person and in accordance with the 

latest regulations.

1.2  ELECTRICAL SUPPLY

Please ensure that this appliance has been properly connected 

to the electrical supply by means of a double pole isolator or 

un-switched socket, and that the correct size of fuse (3 AMP) 

has been fitted.

Warning: this appliance must be earthed!

 

1.3  WARRANTY REGISTRATION

Please take the time to register the appliance warranty using 

the documentation provided, call 0800 479 0754 (UK) or 056 

7755055  to  obtain  your  warranty  confirmation  code  (please 

have your appliance warranty card to hand). 

1.4  APPLIANCE COMMISSIONING 

CHECKLIST (UK only)

The Benchmark checklist section can be found at the rear of 

the appliance installation booklet. This important document 

must be completed during the installation/commissioning of 

your boiler. All GAS SAFE registered installers carry a GAS 

SAFE ID card, and have a registration number. These details 

should be recorded in the Benchmark commissioning checklist 

section within the installation booklet. You can check your 

installers details by calling GAS SAFE direct on 08004085500. 

Failure to install and commission the appliance in accordance 

with the manufacturers instructions will invalidate the warranty. 

This does not affect your statutory rights.

1.5  HOW DOES IT WORK?

Your 

UNICA MAX

 boiler supplies heated water to your radiators 

and hot water cylinder. The appliance is controlled via a timer 

or programmer and any thermostats that your installer may 

have fitted. The boiler will light when it receives a request from 

the timer, programmer, or thermostat that your installer has 

fitted.

 Your 

UNICA MAX

 boiler lights electronically and does 

not have a pilot light.

In the unlikely event of a fault developing with your boiler, the 

supply of gas to the burner will be terminated automatically.

1.6  DIMENSIONS

HEIGHT

WIDTH

DEPTH

20S

740 mm

420 mm

275 mm

30S

740 mm

470 mm

350 mm

1.7  CLEARANCES REQUIRED

*  25mm  above  flue  bend 

if top flue outlet is used. 

Consideration should 

be given to providing 

reasonable clearance 

for the insertion of a FGA 

probe.

** Disconnection 

of 

adjacent components 

may be required in 

order to facilitate syphon 

removal.

*** Provided that a door or 

removal panel enables 

450mm access for 

maintenance.

^ Can be reduced to 

5mm if a removal panel 

enables 100mm for 

maintenance.

2

25

2

100

ABOVE

25mm*

BELOW

100mm^

LEFT SIDE

2mm

RIGHT SIDE 2mm**
FRONT

4mm***

Содержание 41-364-13

























































Отзывы: