background image

14

OPERATION

USING THE SPRAY WAND TRIGGER

See Figure 14.

For  greater  control  and  safety,  keep  both  hands  on  the  
trigger handle at all times.

  Pull back and hold the trigger to operate the pressure 

washer.

  Release the trigger to stop the flow

 of water through the 

nozzle.

To engage the lock out:

  Pull the lock out until it clicks into the slot.

To disengage the lock out:

  Push the lock out down and into its original position.

For the most effective cleaning, the spray nozzle should be 

between 8 in. and 4 in. from the surface to be cleaned. If 
the spray is too close it can damage the cleaning surface.

USING THE NOZZLES

See Figure 15 - 16.

Before starting any cleaning job, determine the best nozzle 
for  the  job.  Each  of  the  nozzles  has  a  different  spray 
pattern. The nozzle patterns are: 5˚ (for general purpose or 
large surfaces), 15˚ (for tough jobs), 0˚ (for spot cleaning or 
high-to-reach areas), and the Dual Power Soap Nozzle (for 
long and short range detergent application).

NOTE:

  For  a  gentle  rinse,  select  the 

Dual  Power  Soap 

Nozzle

 

CAUTION:

NEVER  change  nozzles  without  locking  the  lock 
out on the trigger handle.

Using the quick-connect collar, changing nozzles is easy.

  Turn  off  the  pressure  washer  and  shut  off  the  water  

supply. Pull trigger to release water pressure.

To connect a nozzle to the trigger handle:

  Engage the lock out on the trigger handle by pushing up 

on the lock out until it clicks into the slot.

  Push the nozzle into the quick-connect collar until it clicks 

in place and is secured properly.

To disconnect a nozzle from the trigger handle once the 

cleaning job is complete:

 

Turn  off  the  pressure  washer  and  shut  off  the  water  
supply. Pull trigger to release water pressure.

  Engage the lock out on the trigger handle by pushing up 

on the lock out until it clicks into the slot.

  Remove  the 

nozzle  by  placing  hand  over  nozzle  then 

pulling back the quick-connect collar. 

SLOT

NOzzLE

QuICK-CONNECT 

COLLAR

SPRAY 

wAND

TRIGGER

“CLICK”

LOCK OuT

Fig. 16

Fig. 15

Fig. 14

DuAL POwER 

SOAP NOzzLE

SHORT RANGE 

DETERGENT 

 APPLICATION

LONG RANGE 

DETERGENT 

 APPLICATION

Содержание RD80746



























Отзывы: