Ricoh D067 Скачать руководство пользователя страница 589

Страница: 589 / 676

Bit Switches

D067/D068/D069/D072 7-50

Appendix

CTC transmission conditions

0: After one PPR signal

received

1: After four PPR signals

received (ITU-T standard)

0: When using ECM in non-standard (NSF/NSS)

mode, the machine sends a CTC to drop back the

modem rate after receiving a PPR, if the following

condition is met in communications at 14.4, 12.0,

9.6, and 7.2 kbps.

NTransmit- Number of transmitted frames

NResend- Number of frames to be retransmitted

1: When using ECM, the machine sends a CTC to

drop back the modem rate after receiving four

PPRs.

PPR, CTC: These are ECM protocol signals.

This bit is not effective in V.34 communications.

Modem rate used for the next

page after receiving a negative

code (RTN or PIN)

0: No change 1: Fallback

1: The machine’s tx modem rate will fall back

before sending the next page if a negative code is

received. This bit is ignored if ECM is being used.

Not Used

Do not change the settings

Select detection of reverse

polarity in ringing

0: Off

1: On

This switch is used to prevent reverse polarity in

ringing on the phone line (applied to PSTN-G3

ringing). Do not change this setting

0: No detection Outside Japan

1: Detection Inside Japan only

Содержание D067





































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание D067

Отзывы:

Бренды по названию

Популярные бренды

Ricoh D067, Руководство по обслуживанию

Результаты поиска

Содержание D067

Отзывы:

Бренды по названию

Популярные бренды