Rich electric Invertek CombiPlus Скачать руководство пользователя страница 98

Страница: 98 / 128

Page 98

E7 Group (Aux-Relay 1 Option)

E7-01: Aux-Relay 1 Usage Select

Main Menu>Programming>ENT>Aux-Relay>ENT

Setting Function

E7-01=0

(Initial setting)

Auxiliary Relay 1 is not allowed to be active (Idle).

E7-01=1

Auxiliary Relay 1 is allowed to be active.

E7-02: Aux-Relay 1 Invert Select

Main Menu>Programming>ENT>Aux-Relay>ENT

Setting Function

E7-02=0

(Initial setting)

Auxiliary Relay 1 is normal.

E7-02=1

Auxiliary Relay 1 is Invert switch and that is ON becomes off

and OFF becomes ON.

This is used to invert the Aux-Relay 1 So ON becomes OFF and OFF becomes ON. In the

program, the labels are adapted to reflect this inversion.

E7-03: Aux1 not Switch Off Time (Aux-Relay 1 does not switch off with certain period)

Main Menu>Programming>ENT>Aux-Relay>ENT

Use constant E7-03 to determine the minimum ON time.

The Aux-Relay 1 will not be switched off within the time specified here measured from the

moment that all on condition are inactive.

※

Note: OFF conditions with a delay of 0 minute, ignore this setting.

E8 Group (Aux-Relay 2 Option)
E9 Group (Aux-Relay 3 Option)

※

The functions and the settings of E8 and E9 Groups are exactly the same as those
of E7 Group so please refer to above E7 Group description and setting for E8 and
E9 Groups.

Содержание Invertek CombiPlus





























































































































Результаты поиска

Содержание Invertek CombiPlus

Отзывы:

Бренды по названию

Популярные бренды

Rich electric Invertek CombiPlus, Руководство пользователя

Результаты поиска

Содержание Invertek CombiPlus

Отзывы:

Бренды по названию

Популярные бренды