Rich electric Invertek CombiPlus Скачать руководство пользователя страница 26

Страница: 26 / 128

Page 26

1.16 Ventilation (Standard Single Unit)

When the unit is installed in an

Environment with good ventilation,

The fan cover is not needed.

1.17 Ventilation (Optional Fan Cover Application) “Single Unit Installed”

When the unit is installed nearby wall side which

Blocks the airflow coming to the unit,

The fan cover is needed.

The CombiPlus also supports connection of an

External fan. This is very useful when the

CombiPlus is installed in a cabinet or

in Recreational Vehicle / Boat.

Fan ON:

E1-08, See page 92.

Fan OFF:

E2-08, See page 95.

Aux-Relay 1 can be used to turn ON, when the internal fan switches on.

E1-08: Fan ON for ? sec used together with the E2-08: Fan OFF for ? sec setting to control an

external fan.

Содержание Invertek CombiPlus





























































































































Результаты поиска

Содержание Invertek CombiPlus

Отзывы:

Бренды по названию

Популярные бренды

Rich electric Invertek CombiPlus, Руководство пользователя

Результаты поиска

Содержание Invertek CombiPlus

Отзывы:

Бренды по названию

Популярные бренды