Rich electric Invertek CombiPlus Скачать руководство пользователя страница 81

Страница: 81 / 128

Page 81

B2-09: AC IN Dynamic Power Shifting

Main Menu>Programming>ENT>General>ENT>Auto transfer Switch>ENT

This setting is an expansion of the AC IN Current Limit (B2-05) mechanism.

Setting Function

B2-09=0

(Initial setting)

The AC current limit is specified by the AC IN Current

Limit (B2-05) setting

B2-09=1

The effective AC input current limit depends on the load

history. When the load is lower than the AC IN Current

Limit (B2-05), the effective AC input current limit is also

lower but slightly above the load.

When the load increase, the effective current limit also

increases with a delay. The thought behind this is that when

a generator is running at a low load, it can’t switch to full

load immediately and it needs some time to increase the

power.

An example:

We have a 2KVA generator.

We adjust the AC IN Current Limit (B2-05) setting to 8A and we enable Power Support

(C1-05=1). We have no load connected and the batteries are fully charged. Therefore, no current

from generator is drawn.

At this moment, we connect a load of 7A to the CombiPlus® with this setting

(

B2-09) disabled,

the CombiPlus® would not react because the load is below the AC IN Current Limit (B2-05)

setting. The result is that the full load is connected to generator which will drop in voltage

because it can’t deliver that current instantly which could result in switching to INVERTER.

If however we had this setting (Dynamic Power Shifting) enabled, the effective AC input

current limit would be far lower than 8A because the load was zero. So connecting a load of 7A

will result in CombiPlus® starting to power Support and no voltage drop is being examined on

the AC OUT. The generator starts to supply the load and the effective AC input current limit

will increase to 8A slowly. At the moment, the CombiPlus® will stop Power Support and the

full load is on the generator.

This is powerful option in combination with Power Support but even without Power Support, it

can prevent unnecessary switching to INVERTER because the charge current will reduce when

AC input current becomes higher than the effective AC input current limit.

Содержание Invertek CombiPlus





























































































































Результаты поиска

Содержание Invertek CombiPlus

Отзывы:

Бренды по названию

Популярные бренды

Rich electric Invertek CombiPlus, Руководство пользователя

Результаты поиска

Содержание Invertek CombiPlus

Отзывы:

Бренды по названию

Популярные бренды