Rice Lake iRev 920i Скачать руководство пользователя страница 48

Страница: 48 / 101

920i

Installation Manual

6.2

Default Print Formats

Table 6-2 shows the default print formats for the

920i

and lists the conditions under which each print format is

used. The HDR1FMT and HDR2FMT formats are used to specify header information that can be used by the
other ticket formats. The contents of the HDR

FMT format can be inserted into any other ticket format using the

<H1> and <H2> formatting commands.

6.3

Customizing Print Formats

The following sections describe procedures for
customizing print formats using the

iRev

conÞguration

utility, serial commands, or the front panel (PFORMT
menu. See Section 10.5 on page 85 for information
about custom stream formatting.

6.3.1

Using iRev

The

iRev

conÞguration utility provides a ticket

formatting grid with a tool bar. The grid allows you to
construct the ticket format without using the
formatting commands (<NL> and <SP>) required by
the front panel or serial command methods. Using

iRev

, you can type text directly into the grid, then

select weight value Þelds from the tool bar and place
them where you want them to appear on the printed
ticket.

Figure 6-1 shows an example of the

iRev

formatting display.

Figure 6-1. iRev Print Formatting Display

Format

Default Format String

Used When

GFMT

GROSS<G><NL2><TD><NL>

Normal mode, no tare in system

NFMT

GROSS<G><NL>TARE<SP><T><NL>NET<SP2><N>
<NL2><TD><NL>

Normal mode, tare in system

ACCFMT

ACCUM<A><NL><DA><TI><NL>

Accumulator enabled and displayed

SPFMT

Setpoint push print operation (PSHPRNT=ON)

TRWIN

<NL>ID<SP><TID><NL2>GROSS<TR1>
<NL2><DA><SP><TI><NL>

Press the

Weigh In

softkey, enter truck ID

number, and press

enter

TRWOUT

<NL6>ID<SP><TID><NL2>GROSS<TR1><NL>TARE<SP><TR2
><NL>NET<SP2><TR3><NL2><DA><SP><TI><NL>

Press the

Weigh Out

softkey, enter truck ID

number, and press

enter

TRFMT

REG ID: <TID>: <TR2> SCALE<S> <TD><NL>

Truck register currently displayed

HDR1FMT
HDR2FMT

COMPANY NAME<NL>STREET ADDRESS<NL>
CITY, ST ZIP<NL2>

Must be inserted into other print format

AUXFMT

GROSS<G><NL2><TD><NL>

Access only through

iRite

programming

NOTE:

In OIML and CANADA modes, the letters

(preset tare) are automatically inserted after the printed tare weight.

Table 6-2. Default Print Formats

Содержание iRev 920i






































































































Результаты поиска

Содержание iRev 920i

Отзывы:

Rice Lake iRev 920i, Руководство по установке, Страница: 48 / 101

Результаты поиска

Содержание iRev 920i

Отзывы: