REXROTH IndraDyn A Series страница 24 Скачать руководство пользователя

Страница: 24 / 220

3-10

Safety Instructions for Electric Drives and Controls

Rexroth IndraDyn A

3.9

Protection Against Contact with Hot Parts

CAUTION

Housing surfaces could be extremely hot!
Danger of injury! Danger of burns!

⇒

Do not touch housing surfaces near sources of heat!

Danger of burns!

⇒

After switching the equipment off, wait at least ten (10)

minutes to allow it to cool down before touching it.

⇒

Do not touch hot parts of the equipment, such as

housings with integrated heat sinks and resistors.
Danger of burns!

3.10 Protection During Handling and Mounting

Under certain conditions, incorrect handling and mounting of parts and
components may cause injuries.

CAUTION

Risk of injury by incorrect handling! Bodily
harm caused by crushing, shearing, cutting and
mechanical shock!

⇒

Observe general installation and safety instructions

with regard to handling and mounting.

⇒

Use appropriate mounting and transport equipment.

⇒

Take precautions to avoid pinching and crushing.

⇒

Use only appropriate tools. If specified by the product

documentation, special tools must be used.

⇒

Use lifting devices and tools correctly and safely.

⇒

For safe protection wear appropriate protective

clothing, e.g. safety glasses, safety shoes and safety
gloves.

⇒

Never stand under suspended loads.

⇒

Clean up liquids from the floor immediately to prevent

slipping.

Содержание IndraDyn A Series





























































































































































































































Результаты поиска

Содержание IndraDyn A Series

Отзывы:

Похожие инструкции для IndraDyn A Series

Бренды по названию

Популярные бренды

REXROTH IndraDyn A Series, Руководство по планированию проекта

Результаты поиска

Содержание IndraDyn A Series

Отзывы:

Похожие инструкции для IndraDyn A Series

Бренды по названию

Популярные бренды