Renesas M32R/ECU Series страница 241 Скачать руководство пользователя

Страница: 241 / 839

9-36

DMAC

32180 Group User’s Manual (Rev.1.0)

Figure 9.3.3 Transfer Byte Positions

(7) Ring buffer mode

When ring buffer mode is selected, transfer begins from the transfer start address and after performing

transfers 32 times, control returns to the transfer start address, from which transfer operation is repeated. In

this case, however, the five low-order bits of the ring buffer start address must always be B’00000 (if transfer

size = 16 bits, the six low-order bits must be B’000000).

The following describes how addresses are incremented in ring buffer mode.

[1] When the transfer size is 8 bits

The 27 high-order bits of the transfer start address are fixed, and the five low-order bits are incremented

by one at a time. When as transfer proceeds the five low-order bits reach B’11111, they are recycled to

B’00000 by the next increment operation, thus returning to the start address again.

[2] When the transfer size is 16 bits

The 26 high-order bits of the transfer start address are fixed, and the six low-order bits are incremented

by two at a time. When as transfer proceeds the six low-order bits reach B’111110, they are recycled to

B’000000 by the next increment operation, thus returning to the start address again.

If the source address has been set to be incremented, it is the source address that recycles to the start

address; if the destination address has been set to be incremented, it is the destination address that recycles

to the start address. If both source and destination addresses have been set to be incremented, both ad-

dresses recycle to the start address. However, the start address on either side must have their five low-order

bits initially set to B’00000 (if transfer size = 16 bits, the six low-order bits must be B’000000).

During ring buffer mode, the transfer count register is ignored. Once DMA operation starts, the counter operates

in free-run mode, and the transfer continues until the transfer enable bit is cleared to "0" (to disable transfer).

9.3 Functional Description of the DMAC

(5) Transfer count value

The transfer count value is decremented one at a time, irrespective of the size of transfer unit (8 or 16 bits).

(6) Transfer byte positions

When the transfer unit is 8 bits, the LSB of the address register is effective for both source and destination.

(Therefore, in addition to data transfers between even addresses or between odd addresses, data may be

transferred from even address to odd address or vice versa.) When the transfer unit is 16 bits, the LSB of the

address register (= bit 15) is ignored, and data are always transferred in two bytes aligned to the 16-bit bus.

The diagram below shows the valid byte positions in DMA transfer.

b7 b8

b15

8 bits

Source

Destination

8 bits

16 bits

b7 b8

b15

Содержание M32R/ECU Series








































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание M32R/ECU Series

Отзывы:

Похожие инструкции для M32R/ECU Series

Бренды по названию

Популярные бренды

Renesas M32R/ECU Series, Руководство пользователя

Результаты поиска

Содержание M32R/ECU Series

Отзывы:

Похожие инструкции для M32R/ECU Series

Бренды по названию

Популярные бренды