background image

Button functionality 

The following commands can be performed using the remote control at a distance of no more than 7m.  
Point the remote control at the receiver on the right side of the wall-mounted unit. 

Activate and deactivate the indoor unit with the ON / OFF button 
The following settings appear on display: 
 
1.

FAN AUTO    = Fan speed 

2.

SWING          = Oscillating blade  

3.

25.0 °C           = Set temperature  

4.

COOL            = Mode 

On / Off button

 

25.0 

°c 

FAN AUTO 

COOL 

SWING 

Swing button

 

SWING 

25.0 

°c 

FAN AUTO 

COOL 

SWING 

SWING 

SWING 

Functional process 

SWING 

SWING 

The SWING Taste         stops the oscillating blade. When switched on (display          ), 
the cooled air is distributed better in the room. The unit automatically distributes the air 
in a vertical direction only. The air can only be set to be distributed horizontally by 
manually adjusting the vertical plate fins. 

FAN 

When the FAN button      is pressed, 3 different-sized fan symbols or FAN AUTO are visi-
ble on the display. The size of the symbol represents the speed of the fan. Each time 
the button is pressed, the fan speed is reduced. 

Fan button

 

FAN AUTO 

FAN 

FAN 

FAN 

FAN 

25.0 

°c 

FAN 

COOL 

FAN 

Functional process 

SWING 

TEMP. 

Use the COOL mode when you want to cool the room to the desired temperature. 
Reduce the desired temperature by pressing the Temperature button        in 0.5 °C in-
crements. After you hear a beep, the COMP. display begins to blink for approximately 3 
minutes. This waiting period is a forced pause to increase the service life of the com-
pressor and the outdoor part. Once the display stops blinking, the air-conditioner begins 
working. If the temperature in the room falls 1 C° below the set temperature, the regula-
tor switches cooling off. 

SWING 

COOL 

25.0 

°c 

COOL mode

 

COOL 

 TEMP. 

COOL 

l5.5 

25.0 

COOLING 

COOL 

COOL 

Functional process 

FAN 

COOL / DRY 

DRY 

 TEMP. 

DRY 

l5.5 

25.0 

DEHUMIDIFICATION 

COOL / DRY 

Functional process 

The COOL / DRY mode dehumidifies the room in an unregulated fashion. The tem-
perature of the plate fin exchanger of the indoor unit almost always falls below the dew 
point of the air which causes the moisture in the air to condense on the plate fins. 
The dehumidification capacity is based on the moisture in the air and the room tem-
perature. After the DRY button       has been pressed, the desired temperature can be 
selected and the unit begins working. The fan switches off at specific intervals to lower 
the plate fin temperature. You can exit this mode by switching to a different one. 

25.0 

COOL / DRY mode

 

DRY 

SWING 

COOL / DRY 

°c 

FAN AUTO 

Содержание RKV 13 T





















Отзывы: