background image

 

 

Before any work on the units is performed, they must be disconnected from the power supply 

(fuse or repair switch) and prevented from being inadvertently switched on

!

 

Troubleshooting 

 
This unit has been designed based on state-of-the-art manufacturing methods and it has been tested repeatedly to 
ensure that it is working properly. However, should problems occur, refer to the following list. 

Should the unit still not work after performing these functional checks, please contact the closest dealer or 

REMKO GmbH & Co KG. directly. See also section “Customer Service and Guarantee“. 

Problem 

Possible cause 

Check 

Remedy 

The unit does not start or it 
switches itself off automatically. 

Power failure, power too low  

Are all other electrical components 
working? 

Check current and wait for the de-
vice to start again 

Power fuse / power supply defec-
tive 

Are all currents for lighting func-
tional? 

Replace power fuse / 
Switch on main switch 

Power supply line damaged 

Are all other electrical components 
working? 

Maintenance by authorised per-
sonnel 

Amount of time waited after 
switching unit on was too short 

Plan for longer waiting periods 

Restart after approximately 5 min. 

Operating temperature too low / 
too high 

Are the fans still working? 

Observed temperature range be-
tween 15 and 30 °C  

The indoor unit is not respond-
ing to the remote control. 

Timer set to “ON” 

Is the timer set? 

Delete programming and restart 

Excess current caused by thunder-
storms 

Was there recently lightning in the 
region ? 

Switch the system off and then back 
on again 

Polarity of batteries incorrect after 
replacement 

Is the polarity incorrect? 

Insert batteries with the correct 
polarity 

Transmission distance too great / 
reception blocked 

Is the transmission signal at a dis-
tance of approx. 3 m when the but-
ton is pressed? 

Reduce distance to under 6 m and 
change location 

Remote control defective 

Does the unit work in manual 
mode? 

Replace remote control 

Too much direct sunlight on the 
receiver or transmitter 

Does the function work in the 
shade? 

Place the transmitter or receiver in 
the shade 

Electromagnetic fields are disrupt-
ing transmission 

Does the unit work after potential 
causes of disruption have been 
eliminated? 

No signal transmission when 
sources of disruption are operated 
simultaneously 

Remote control buttons stuck / two 
buttons pressed at once 

Does the symbol      appear on the 
display? 

Unstick button / only press one 
button 

Dead batteries in the remote con-
trol 

Are the batteries new? Is the dis-
play incomplete? 

Insert new batteries 

Temperature setting too high 

Is the selected temperature above 
the room temperature? 

Reduce selected temperature 

The unit is operating at a low 
cooling capacity. 

Filter is dirty/ intake / outlet open-
ing is blocked by foreign bodies 

Have the filters been cleaned? 

Clean filters 

Windows and doors are opened / 
increased amount of warm air or 
cold air 

Have there been changes in de-
sign or use? 

Close the windows and doors / 
mount additional systems 

Cool mode is not set 

Does the Cool symbol (COOL) 
appear on the display? 

Correct the unit settings 

Condensation water is leaking 
from the indoor unit. 

The drainage line of the condensa-
tion collector is blocked / damaged  

Can condensation drain freely? 

Clean the drainage line and the 
condensation collector 

External condensation pump or 
float regulator is defective 

Is the collector filled with water 
and the pump is not working? 

Have pump checked by authorised 
service centre 

Содержание RKV 13 T





















Отзывы: