![background image](http://html.mh-extra.com/html/remington/500/500_operating-manual_1438538012.webp)
12
S
ection
2 — A
SSembly
& S
et
-U
p
Set-Up
Chute Control Cable Routing (If
Equipped)
For units equipped with 2-way or 4-way chute
control joystick, electric chute control and/or
chute-pitch controls, ensure control cables are
routed properly.
Chute control cables are routed through a
single wire guide (a) on top of the engine and/
or through two wire guides (b) located on the
left side of the unit. See Figure 2-41.
NOTE: On units equipped with a cable tie
securing the cables to the rear of the gas tank,
pull the cables toward the chute and pull the
cable tie snug to secure the cables in place.
NOTE: For smoothest operation, cables should
all be to the left of the chute directional
control rod (c).
NOTE:
The number of cables routed through
the wire guides will depend on unit model.
1.
Locate cable guide(s) and perform the
following:
•
Units with Top Mounted Wire Guide (a) -
Check that all cables are properly routed
through cable guide on top of engine.
See Figure 2-41.
•
Units with Side Mounted Wire Guides
(b) - Check that all cables are properly
routed through the wire guide below
the left side of the engine and the wire
guide below the chute control head.
See Figure 2-41.
(b)
(a)
(c)
(c)
(b)
Figure 2-41
Shear Pins Storage (If Equipped)
On select units, holes are provided in the rear
of the handle panel for shear pin (a) and bow-
tie cotter pin (b) storage as shown in Figure
2-42. If not provided, make sure to store them
in a safe place until needed.
(a)
(b)
(a)
(b)
(a)
(b)
Figure 2-42
Drift Cutters (If Equipped)
The drift cutters are mounted inverted at the
factory for shipping purposes.
Standard
1.
Remove two screws (a) and lock nuts (b)
that secure each drift cutter, and remove
them from the sides of auger housing.
See Figure 2-43.
(a)
(a)
(b)
(b)
Figure 2-43
2.
Turn the drift cutters around and
position them as shown in Figure 2-43 to
the outside of the auger housing.
3.
Attach drift cutters with screws (a) and
lock nuts (b) removed in Step 1.
Tool-less
1.
Remove two carriage bolts (a) and wing
nuts (b) that secure each drift cutter, and
remove them from the sides of auger
housing. See Figure 2-44.
(b)
(b)
(a)
(a)
(b)
(b)
(a)
(a)
Tool-less Adjustable
Drift Cutter
Tool-less Non-Adjustable
Drift Cutter
Figure 2-44
2.
Turn the drift cutters around and
position them as shown in Figure 2-44
to the outside of the auger housing.
3.
Attach drift cutters with carriage bolts
(a) and wing nuts (b) removed in Step 1.
Skid Shoes (If Applicable)
Select models require the installation to the
provided skid shoes.
1.
Using the two carriage bolts (a) and
hex flange nuts (b) and flat washers (if
equipped) (c), secure the skid shoe to
the auger housing (d). Hand tighten hex
flange nuts. See Figure 2-45.
2.
Adjust the skid shoe to provide a
minimum of 1/8th inch clearance
between the shave plate (e) and the
ground. Securely tighten hex flange
nuts.
3.
Repeat Step 1 to install the remaining
skid shoe.
4.
If necessary refer to Skid Shoes in the
Adjustments section on page 13.
NOTE: Augers not shown for clarity
(a)
(a)
(c)
(c)
(b)
(b)
(d)
(e)
Figure 2-45