Remcor Cornelius VANGUARD 245 Скачать руководство пользователя страница 35

Страница: 35 / 71

569000203

NOTE:

Do not

confuse syrup and water shutoff valves with dispensing valve flow control adjusting

screws.

NOTE: The dispensing valve water shutoff valve

must

be in the fully “OPEN” position.

LED INDICATOR LIGHT

CANCEL/POUR SWITCH

FIGURE 12. PORTION CONTROL COVER

5. Position volume cup under the dispensing valve nozzle.

6. Dispense from the regular dispensing valve for four-seconds or press “CANCEL/POUR” switch (portion

control dispensing valve) as shown in Figure 12 and hold for four-seconds.

NOTE: 10-fluid ounces (296 ml) of water should have been dispensed into the volume cup for
sugar-based drinks and 7.6-fluid ounces (225-ml) for sugar-free based drinks.

7. If the water volume is correct, proceed with step 8. If the water flow rate is not correct, proceed with step 9.

8. Turn dispensing valve water flow control adjusting screw to the right (CLOCKWISE) to increase water flow

rate or to the left (“COUNTERCLOCKWISE”) to decrease the water flow rate.

NOTE: One (1) turn of the water flow control adjusting screw will change the water flow rate
approximately 2-fluid ounces (59-ml) per 4-second draw.

9. Repeat steps 2 through 7 for each dispensing valve until all valves are checked and/or calibrated (as

required). The water flow rate check is complete.

10. Turn syrup shutoff valve (right-side shutoff valve) to the “OPEN” (extreme CLOCKWISE) position.

11. Install top cover on the dispensing valve and secure with screw.

12. Install front cover on the dispensing valve.

13. Re-connect syrup supply to the dispensing valve

CC–1 Dispensing Valve.

1. Disconnect syrup supply from the dispensing valve the water flow rate check will be performed on.

2. Remove applicable dispensing valve portion control cover by sliding the cover up and off the top cover.

3. Remove dispensing valve top cover by loosening screw securing the cover, then lift cover up and off the

valve.

4. Position volume cup under the dispensing valve nozzle.

Содержание Cornelius VANGUARD 245








































































Результаты поиска

Содержание Cornelius VANGUARD 245

Отзывы:

Remcor Cornelius VANGUARD 245, Инструкция по установке и обслуживанию, Страница: 35 / 71

Результаты поиска

Содержание Cornelius VANGUARD 245

Отзывы: