Remcor Cornelius VANGUARD 245 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 71

Remcor Cornelius VANGUARD 245 Скачать руководство пользователя страница 24

19

569000203

INSTALLING FRONT ACCESS PANEL, SPLASH GUARDS, DRIP TRAY, AND CUP REST

(see applicable Figure 9, 10 or 11)

1. Place front access panel in position on the Unit.

2. Place right-side SPLASH GUARD (item 8) in position on the Unit . Secure splash guard and front access

panel to the Unit with two screws that were removed when removing the front access panel.

LEAVE

SCREWS LOOSE FOR THE TIME BEING

.

3. Place left-side SPLASH GUARD (item 9) in position on the Unit . Secure splash guard and front access

panel to the Unit with other two screws that were removed when removing the front access panel.

LEAVE

SCREWS LOOSE FOR THE TIME BEING

.

4. Install DRIP TRAY (item 2) in drip tray holder as follows:.

IMPORTANT: Before installing Dispenser (Unit P/N 497306660WS) front access panel, make sure the
two-wire electrical wiring harness (see Figure 9) with spade clip terminals on it’s end (intended for
connection to the push-button plain water dispense switch on the drip tray support) is hanging down
out bottom of the Dispenser. This wiring harness

must

be connected to the plain water dispense

switch before installing the drip tray in the drip tray support.

5. Hold DRIP TRAY (item 2) up in position above the drip tray holder.

6. Connect drip tray drain hose to the drip tray and secure with DRAIN HOSE CLAMP (item 13).

7. Place the drip tray so that the two splash guard steps rest on the drip tray edge, then tip back of the drip

tray down and place it’s back edge up under bottom of the loosely installed front access panel.

8. When the drip tray is in this position, work the front corners of the drip tray down until the drip tray sits in

it’s proper position on the the drip tray holder.

9. Tighten all four screws securing the front access panel.

10. Using a silastic sealant (such as Dow Corning RTV 731 or equivalent), seal cracks on outsides of the

splash guards where they enter the drip tray holder.

11. Using a silastic sealant (such as Dow Corning RTV 731 or equivalent), Seal cracks on insides of the splash

guards where the drip tray and the splash guards surfaces meet. Also seal front edge of the drip tray where
it sets on the drip tray holder.

NOTE: Connection of drip tray drain hose to a permanent drain is recommended. Drip tray drain hose
routed to a waste container

is not

recommended due to sanitation and cleaning problems.

The drip tray drain hose

must

be attached to the drain to allow a 3-inch air gap between the drain and

the end of the hose. All connections

must

comply with local plumbing codes and health codes.

12. Preferably, route the lower end of the drip tray drain hose and connect it to a permanent drain.

13. Place CUP REST (item 1) in the drip tray.

CUP HOLDER

(OPTIONAL)

DRIP TRAY

DRIP TRAY HOLDER

CUP REST

STRAW HOLDER

(OPTIONAL)

SPLASH

GUARD

SPLASH

GUARD

PLAIN WATER DISPENSE SWITCH

(DISPENSER 497306660ws)

FIGURE 8. DRIP TRAY INSTALLATION

«
...
22
23
24
25
26
...
»

Содержание Cornelius VANGUARD 245








































































Отзывы:

Нет отзывов