Regency P36-NG4 Скачать руководство пользователя

Страница: 36 / 64

FPI P36-4 Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

CONVERSION KIT #514-969 FROM NG TO LP

FOR P36-4 USING SIT 820 NOVA GAS VALVE

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !!

Shut off the gas supply.

Remove the louvers (and bay door if it is
installed).

Open the fl ush door and remove the
door.

Remove the logs and embers (if already
installed).

Remove the 2 screws, push Burner Assembly

to the left and lift out.

Pull off the pilot cap to expose the pilot
orifi ce.

Unscrew the pilot orifi ce with the allen
key; then replace with the LPG pilot
orifi ce and the pilot cap, provided in the
kit.

Remove burner orifi ce with a 1/2"
wrench. Use another wrench to hold on
to the elbow behind the orifi ce. Discard
orifi ce.

Burner Orifi ce

Each Kit contains one LPG
Conversion Kit and one DC
Sparker Kit.

Conversion Kit Contains:
Qty. Part #

Description

904-390

Burner Orifi ce #52

904-529 5/32"

Allen

Key

918-590 Decal

"Converted

LPG"

908-528 Red

"LPG"

label

910-037 LPG

Injector

(Pilot

Orifi

ce)

918-481 Instruction

Sheet

Remove the 2 screws holding the Burner
Assembly to the fi rebox base. Push the
Burner Assembly to the left and lift out.

DC Sparker Kit Contains:

Qty. Part #

Description

820-475

Bracket DC Sparker

820-476

Bracket DC Sparker

904-153

Washer #8 External Star

904-330 Nut

8-32

Hex

904-531

Bushing Split Plastic

0.500

in.

904-543

Screw 8-32 x 3/4 Pan

Head

904-553

Screw #8 x 1/2 Type "B",

Black

Oxide

910-073

Spark Generator Battery

Holder

910-074

Spark Generator Switch

C/W

Wire

910-078 Battery

Size

Energizer En91

910-199 Clip

Wire

Holder

910-903

Wire Fan To Power Cord

Ground 30 in.

904-781

Velcro Hook, Black

904-782

Velcro Hook, Black

Installation of LPG
Conversion Kit:

For P36D-1 / P36-4 Only:

For U32-5 Only:

5a)

Remove the grate by removing the

screws on each side of the grate.

Remove the 2 screws,

push Burner Tray to the left, and lift off.

Remove the 2 screws

holding the grate in position.

5b)

Remove the Burner Tray by removing

the screws on each side of the tray.
Push the tray to the left and lift up.

IMPORTANT

Before re-installation of the burner (once

the LP conversion is complete), the air

defl ector must be installed. See step 18a.

Содержание P36-NG4

































































Результаты поиска

Содержание P36-NG4

Отзывы:

Похожие инструкции для P36-NG4

Бренды по названию

Популярные бренды

Regency P36-NG4, Инструкция для владельца и по установке

Результаты поиска

Содержание P36-NG4

Отзывы:

Похожие инструкции для P36-NG4

Бренды по названию

Популярные бренды