Regency P36-NG4 Скачать руководство пользователя

Страница: 53 / 64

FPI P36-4 Zero Clearance Direct Vent Gas Fireplace

REGENCY

OPTIONS

FLUSH TRIM

Attach the round magnets to the back of the top
trim piece and to the bottom trim piece, then
attach trim to the top and bottom of fl ush door.

FLUSH LOUVERS

Install the top louver by sliding the two

bracket clips into the brackets located
underneath the top of the fi rebox.

The bottom louver has a hinge that is

attached (2 screws per hinge) to the lip on
bottom of the unit.

Open the bottom louver. Pull the Burner

ON/OFF control box from inside the bottom
of the fi replace and position the slots in the
bracket over the 2 screws on the left side of
the bottom louver. Push down to lock into
place. Tighten the screws.

Burner ON/OFF

control box

Screws on

louver bracket

Note: Top and
bottom louvers
are different.

Содержание P36-NG4

































































Результаты поиска

Содержание P36-NG4

Отзывы:

Похожие инструкции для P36-NG4

Бренды по названию

Популярные бренды

Regency P36-NG4, Инструкция для владельца и по установке

Результаты поиска

Содержание P36-NG4

Отзывы:

Похожие инструкции для P36-NG4

Бренды по названию

Популярные бренды