Regency P121-LP10 Скачать руководство пользователя страница 27

Страница: 27 / 48

Regency

P121-10/P131-10 Zero Clearance Direct Vent Gas Fireplace

installation

CONVERSION FROM NG TO LP

FOR P121-10/P131-10 USING SIT 829 NOVA GAS VALVE

919-499

12/03/14

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION !!

Pull off the pilot

cap to expose

the pilot orifice.

Unscrew the pilot orifice with the allen key

and replace with the LPG pilot orifice in

the kit and replace pilot cap.

Remove burner orifice with a 1/2" wrench

to hold onto the elbow behind the orifice

and discard the orifice.

Burner Orifice

Remove the louvers and trim kit. Remove

the safety screen and glass door.

Remove the logs, embers.

P121 / P131

Each Kit contains one LP

Conversion Kit

LP Conversion Kit Contains:

Qty. Part #

Description

1 904-529

5/32" Allen Key

1 904-641

Burner Orifice #50

1 918-590

Decal "Converted to

LPG"

1 908-528

Red "LPG" label

1 910-037

LPG Injector

(Pilot Orifice

1 910-582

LPG Stepper Motor

1 919-499

Instruction Sheet

Diagram 1 and 2: Remove the left and right

screws and then slide the burner assembly

away from the orifice and lift out.

Remove the burner assembly by remov

ing the 4 screws - then slide the burner

assembly away from the orifice and lift

out.

Reinstall new burner orifice LPG stamped

#50 and tighten.

10.

Turn control knob to the “OFF” position.

Conversion from NG to LPG

for P121-10 / P131-10 using SIT 829 NOVA Gas Valve

Remove the grate by lifting straight up.

Remove the side brick panels (if

installed). The

brick panel is very

fragile - handle with care.

Installation of LPG

Conversion Kit:

Diagram 1

Diagram 2

Diagram 3

Diagram 4

Diagram 5

12.

Reverse steps 4) to 1).

13.

Attach the label "This unit has been

converted to LPG" near or on top of the

serial # decal.

14.

Replace yellow "NG" label with red "LPG"

label.

15.

Check for gas leaks.

16.

Check inlet and outlet pressures.

17.

Check operation of flame control.

18.

Check for proper flame appearance and

glow on logs.

WARNING!

Also check that the pilot and main burner

injectors are appropriate for the gas

type.

11.

Remove NG stepper motor by removing 3

screws in locations shown below–replace

with LP stepper motor, secure in place with

3 screws.

Remove NG Stepper motor and

replace with LP Stepper motor

. Remove pilot clip below pilot cap.

Clip

Pilot Cap

Installer Notice:

These instructions must be left

with the appliance.

Содержание P121-LP10

















































Результаты поиска

Содержание P121-LP10

Отзывы:

Похожие инструкции для P121-LP10

Бренды по названию

Популярные бренды

Regency P121-LP10, Инструкция для владельца и по установке

Результаты поиска

Содержание P121-LP10

Отзывы:

Похожие инструкции для P121-LP10

Бренды по названию

Популярные бренды