Regency HZ33CE-LP10 Скачать руководство пользователя страница 29

Страница: 29 / 56

Regency HZ33CE-10 Gas Fireplace

installation

Riser Vent

Termination

Min. 6-1/4"*

(159mm)

Diagram 3

UNIT INSTALLATION WITH HORIZONTAL TERMINATION

Diagram 1

Mark the wall for a 10" x 10" square hole.

The center of the square hole should line

up with the centerline of the horizontal pipe.

Cut and frame the 10 inch square hole

in the exterior wall where the vent will be

terminated. If the wall being penetrated is

constructed of non-combustible material, i.e.

masonry block or concrete, a 7"(178mm)

diameter (7-1/2"(191mm) dia. for flex) hole

is acceptable.

Note:

The horizontal run of vent must be level,

or have a 1/4 inch rise for every 1 foot

of run towards the termination. Never

allow the vent to run downward. This

could cause high temperatures and may

present the possibility of a fire.

The location of the horizontal vent

termination on an exterior wall must meet

all local and national building codes,

and must not be blocked or obstructed.

See "Exterior Vent Terminal Locations"

Section.

Snorkel Terminations:

For installations requiring a vertical rise

on the exterior of the building, 14-inch

and 36-inch tall Snorkel Terminations

and the Riser Vent as shown in

Dia. 2 & 2a are available. Follow the

same installation procedures as used

for standard Horizontal Termination.

NEVER install the snorkel upside down.

Below Grade Snorkel Installation

If the Snorkel Termination must be

installed below grade, i.e. basement

*As specified in CGA B149 Installation Code.

Local codes or regulations may require different

clearances.

Diagram 2

application, proper drainage must

be provided to prevent water from

entering the Snorkel Termination. Refer

to Snorkel Installation instructions for

details. Do not attempt to enclose the

Snorkel within the wall, or any other

type of enclosure.

The arrow on the vent cap should

be pointing up.

Insure that the 1-1/2"

clearances to combustible materials are

maintained (Dia. 3.. Install the termination

cap.

AstroCap

or all other approved

Horizontal Termination Caps may be used.

The four wood screws provided should

be replaced with appropriate fasteners for

stucco, brick, concrete, or other types of

sidings.

Diagram 2a

Install the vent system according to the

manufacturer's instructions included with the

components.

Set the unit in its desired location. Check

to determine if wall studs or roof rafters

are in the way when the venting system is

attached. If this is the case, you may want

to adjust the location of the unit. Rough in

the gas preferably on the right side of the

unit and the electrical (junction block is on

the left side) on the left.

Direct Vent pipe and fittings are designed with

special twist-lock connections to connect the

venting system to the appliance flue outlet. A

twist-lock appliance adaptor is an available

option that must be used in conjunction with

the Simpson Dura-Vent Direct Vent system.

Put a bead of silicone inside the outer section

of the adapter and a bead of Fireplace Mate

on the inner collar. Slip the adapter over the

existing inner and outer flue collar and fasten

to the outer collar only with the 3 supplied

screws (drilling pilot holes will make this

easier). Level the fireplace and fasten it to

the framing using nails or screws through

the nailing strips.

Assemble the desired combination of pipe

and elbows to the appliance adaptor and

twist-lock for a solid connection.

Note:

Twist-lock procedure: Four indentations,

located on the female ends of pipes and

fittings, are designed to slide straight

onto the male ends of adjacent pipes

and fittings, by orienting the four pipe

indentations so they match and slide

in to the four entry slots on the male

ends, Dia. 1. Push the pipe sections

completely together, then twist-lock

one section clockwise approximately

one-quarter turn, until the two sections

are fully locked. The female locking lugs

will not be visible from the outside, on

the Black Pipe or fittings. They may be

located by examining the inside of the

female ends.

NOTE:

For best results and optimum

performance with each approved venting

system, it is highly recommended to apply

“Mill-Pac” sealant (supplied) to every inner

pipe connection. Failure to do so may result

in drafting or performance issues not cov

ered under warranty.

Horizontal runs of vent must be

supported every three feet. Wall straps

are available for this purpose.

Note: If installing termination on a siding

covered wall, a vinyl siding standoff

or furring strips must be used to

ensure that the termination is not

recessed into the siding.

Before connecting the horizontal run of vent

pipe to the vent termination, slide the Wall

Thimble over the vent pipe.

Содержание HZ33CE-LP10

























































Результаты поиска

Содержание HZ33CE-LP10

Отзывы:

Похожие инструкции для HZ33CE-LP10

Бренды по названию

Популярные бренды

Regency HZ33CE-LP10, Инструкция для владельца и по установке

Результаты поиска

Содержание HZ33CE-LP10

Отзывы:

Похожие инструкции для HZ33CE-LP10

Бренды по названию

Популярные бренды