Regency HZ33CE-LP10 Скачать руководство пользователя страница 32

Страница: 32 / 56

Regency HZ33CE-10 Gas Fireplace

installation

CONVERSION KIT# 438-971 FROM NG TO LP

For HZ33CE using SIT 885 NOVA Gas Valve

Conversion from NG to LPG

for HZ33CE using SIT 885 NOVA Gas Valve

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION !!

Remove regulator and discard. Install Hi/

Lo pressure regulator onto the valve with

2 screws as shown below.

Installer Notice:

These instructions must be left

with the appliance

Each Kit contains one LPG

Conversion Kit # 438-971

LPG Conversion Kit Contains:

Qty. Part #

Description

904-241

Burner Orifi ce #56

918-590

Decal "Converted to

LPG"

908-528

Red "LPG" label

904-529

5/32" Allen Key

910-101

LPG Injector

(Pilot Orifi ce)

911-011

Stepper Motor

919-433

Instruction Sheet

Installation of the LPG

Conversion Kit:

Shut off the gas supply

a) Remove the mesh barrier and glass

door.

b) Remove the Glass Crystals or

Ceramic Stones. Also remove

Inner Panels - if installed.

c) Remove the six (6) screws in locations

shown below to remove burner tray.

Unscrew the pilot orifi ce with the Allen

key and replace with the LPG pilot

orifi ce in the kit and replace pilot cap.

Remove burner orifi ce with a 1/2"

wrench and discard. Use another

wrench to hold on to the elbow below

the orifi ce.

Burner Orifi ce

Install the new burner orifi ce stamped

#56.

Pull off the pilot cap to expose the pilot

orifi ce.

Remove the wire clip below the pilot cap.

Diagram 2

Diagram 5

Diagram 3

Diagram 6

Diagram 4

Diagram 7

Diagram 8

Diagram 1

3. Remove 2 screws in location shown in

below - slide burner to the right then lift
out. (See Diagram 2)

10.

Attach the label “This unit has been

converted to LPG” near or on top of the

serial # decal

11.

Replace yellow “NG” label with red

“LPG” label

12.

Reverse steps 2 - 1.

13.

Check for gas leaks.

14.

Check inlet and outlet pressures.

15.

Check operation of fl ame control.

Pilot retainer clip

919-433

06.09.14

HZ33CE

Содержание HZ33CE-LP10

























































Результаты поиска

Содержание HZ33CE-LP10

Отзывы:

Похожие инструкции для HZ33CE-LP10

Бренды по названию

Популярные бренды

Regency HZ33CE-LP10, Инструкция для владельца и по установке

Результаты поиска

Содержание HZ33CE-LP10

Отзывы:

Похожие инструкции для HZ33CE-LP10

Бренды по названию

Популярные бренды