Regency HZ33CE-LP10 Скачать руководство пользователя страница 10

Страница: 10 / 56

Regency HZ33CE-10 Gas Fireplace

installation

Caution Requirements

The top, back and sides of the fireplace are defined by

standoffs. The metal ends of the standoff may

NOT

be recessed into combustible construction.

WARNING

Fire hazard is an extreme risk

if these clearances (air space) to combustible materials are not

adhered to. It is of greatest importance that this fireplace and vent

system be installed only in accordance with these instructions.

CLEARANCES

The clearances listed below are Minimum distances unless otherwise stated:

A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest

importance that this fireplace and vent system be installed only in accordance with these instructions.

Clearance:

Dimension

Measured From:

A: *Front Floor Clearance (min.)

Underside of Unit

B: *Sidewall (on one side)

9" (229mm)

Side Opening of Unit

C: *Ceiling

(room and/or alcove)

30" (762mm)

Top Opening of Unit

D: Alcove Width

84" (1219mm)

Sidewall to Sidewall (Minimum)

E: Alcove Depth

36" (914mm)

Front to Back Wall (Maximum)

F: Mantel

12" (305mm)

G: Mantel Clearances

15-3/4" (400mm)

From Top Opening of Unit

Close to Ceiling

Flue Clearances

Horizontal - Top

2-1/2"

Horiztonal - Side

1-1/2"

Horiztonal - Bottom

1-1/2"

Vertical (Flex Vent)

1-1/2"

Vertical (Rigid)

1-1/4"

Содержание HZ33CE-LP10

























































Результаты поиска

Содержание HZ33CE-LP10

Отзывы:

Похожие инструкции для HZ33CE-LP10

Бренды по названию

Популярные бренды

Regency HZ33CE-LP10, Инструкция для владельца и по установке

Результаты поиска

Содержание HZ33CE-LP10

Отзывы:

Похожие инструкции для HZ33CE-LP10

Бренды по названию

Популярные бренды